We apply steady and time-periodic blowing, respectively, to flow over a circular cylinder at a Reynolds number of 21 000 for the modification of flow in the wake. The blowing is applied near the separation point on the upper and lower surfaces from either a slit (uniform blowing) or eight holes (discrete blowing) along the spanwise direction at each surface. For steady blowing, the blowing momentum coefficient ranges from 0.008 to 0.269, and, for time-periodic blowing, it does from 0.013 to 0.162. The changes in the drag are estimated by a momentum theorem with the velocity measurements in the wake. The steady discrete blowing is more effective and efficient for drag reduction than the steady uniform blowing, providing a maximum drag reduction of 38%. Counter-rotating vortices induced by the optimal discrete blowing change the Kármán vortex cores into three-dimensional vortices and weaken their strength. On the other hand, steady uniform blowing significantly increases the wake width and leads to drag increase. With time-periodic blowing, the maximum drag reductions by uniform and discrete blowing are 68% and 28%, respectively, indicating that the time-periodic uniform blowing is more effective than the steady discrete blowing. For the time-periodic blowing, two different vortex lock-on phenomena (symmetric and asymmetric vortex shedding in the wake) are found, and they lead to a significant drag decrease and increase, respectively.
This work aims to experimentally investigate the manipulation of a turbulent boundary layer over a flat plate using a proportional-derivative (PD) controller. The control action is generated by an array of two flush-mounted piezo-ceramic actuators. Two different schemes are examined, i.e., feed-forward and feedback PD controls, with a view to suppressing the viscous-scaled near-wall cycle of high-speed events in the near-wall region and hence reducing skin friction drag. It has been found that the use of the feed-forward PD scheme may reduce the local maximum drag reduction by up to 33% at 14 wall units downstream of the actuator array, exceeding the open-loop control result (30%) as well as our previously reported combined feed-forward and feedback scheme (28%) [Z. X. Qiao, Y. Zhou, and Z. Wu, “Turbulent boundary layer under the control of different schemes,” Proc. R. Soc. A 473, 20170038 (2017)], and furthermore, this significantly cuts down the required input energy by 27%, compared to the open-loop control. On the other hand, the feedback PD scheme achieves the same control performance as the open-loop control, that is, producing a local maximum drag reduction of 30% without any saving in the input energy. The underlying control mechanism behind these control schemes is proposed based on the analyses of the hot-wire data measured with and without control.
This work aims to investigate experimentally the effect of the Reynolds numberRe,based on the nozzle diameterD, on jet mixing manipulation using an unsteady radial minijet. A novel artificial intelligence (AI) control system has been developed to manipulate the jet overRe = 5800–40 000. The system may optimize simultaneously the control law and a time-independent parameter, which dictate the actuation ON/OFF states and amplitude, respectively. The control parameters include the mass flow rate, excitation frequency and diameter ratios (Cm,fe/f0andd/D) of the minijet to the main jet as well as the duty cycle (α) of minijet injection. Jet mixing is quantified usingKeandK0, whereKis the decay rate of the jet centreline mean velocity, and subscriptseand 0 denote the manipulated and unforced jets, respectively. It has been found that the maximumKeachievable does not vary withRe.Scaling analysis of the huge volume of experimental data obtained from the AI system reveals that the relationshipKe=g1(Cm,fe/f0,α,d/D, Re, K0) may be reduced toKe/K0 = g2 $(\zeta )$ , whereg1andg2are different functions and the scaling factor $\zeta = ({C_m}/\alpha ){(D/d)^{1 - n}}(1/Re){({f_e}/{f_{e,opt}})^m}$ ,mand 1 − nare the power indices, and subscriptoptdenotes the value at whichKeis maximum. The scaling law is discussed in detail, along with the physical meanings of the dimensionless parametersKe/K0,ζ, $({C_m}/\alpha ){(D/d)^{1 - n}}(1/Re)$ and ${({f_e}/{f_{e,opt}})^m}$ .
We suggest a predictive model of the drag coefficient of a circular cylinder using the information of the mean streamwise velocity and Reynolds normal stresses at a streamwise location in the wake. The boundary layer approximation in the wake and Bernoulli equation in the inviscid region are used to model the contribution from the pressure distribution at the streamwise measurement location. To examine the accuracy of the present model, unsteady three-dimensional numerical simulations are conducted at various Reynolds numbers from laminar to critical regimes. The drag coefficients predicted from the present model agree very well with those from the present numerical simulation.
This work aims to control flow separation from a two-dimensional curved ramp. The Reynolds number examined is Reθ = 5700 based on the momentum thickness of the turbulent boundary layer right before the ramp. Three steady jets, blowing tangentially along the ramp from three spanwise slits, are deployed at the most likely flow separation position, upstream and downstream of this position, respectively. Three different control modes are investigated, i.e., a single jet, multiple jets, and genetic algorithm-optimized blowing rates of three jets. The single jet placed at the time-averaged flow separation position is found to be most effective and efficient in eliminating flow separation among the first and second control modes. However, it is the third control mode that may not only eliminate the separation bubble completely but also cut down the energy consumption, by up to 30%, compared to the single jet blowing at the flow separation position. The flow physics underlying the control modes is also discussed.