The increasing use of recycled tire rubber in construction products requires reliable methods for characterizing its internal structure, particularly porosity, which significantly affects material properties. In composite panels made from rubber granulate and polyurethane binder, porosity is important because of its influence on density, water absorption, thermal and acoustic properties, yet sufficiently adapted and standardized test methods for such materials are currently lacking. This paper proposes a simple pressure-assisted water saturation method for estimating the accessible porosity of panels made from recycled tire rubber. The method is based on saturating the specimen with water under pressure and gravimetrically monitoring mass increase until stabilization. A total of 27 specimens with densities ranging from 585 to 1100 kg/m3 were tested, divided into three groups according to granulometric composition: fine, coarse, and mixed granulation. The results showed a general inverse relationship between density and accessible porosity, whereby lower-density specimens exhibited a higher proportion of pores, while denser specimens showed a smaller volume of water-accessible voids. The highest mean porosity was determined for a density of 585 kg/m3, at 29.832%, while the lowest mean value was recorded for a density of 915 kg/m3, at 16.664%. The proposed method represents a simple and cost-effective application.
31 May 2024 in Urban development and spatial planning
The article considers the prospects of using gypsum-based composite materials for repairing damaged walls of limestone-shell rock buildings. Repairing damaged shell rock structures with cement compositions intensifies destructive processes; the use of lime-sand mixtures for repair work on building facades is problematic due to their prolonged hardening. The article substantiates the use of gypsum as the basis of the repair composition. The use of gypsum composites for exterior works requires a significant increase in their water resistance. A plaster mixture based on an ash-cement binder with an addition of lime is proposed; a series of samples with different component contents were made in the planned experiment. Their water resistance was studied using two criteria: the conventional softening coefficient (Кр) and the new one - the water resistance index (Iw); a comparison of these criteria was performed. The significant dependence of these criteria on the measurement conditions, which are not currently standardized, is established. Mathematical models of water resistance characteristics have been built, with the help of which the influence of the content of components on the resistance of the plaster composition to water has been analyzed. To further improve the water resistance of the mixture, a hydrophobizing additive was selected in terms of surface wetting and water absorption. Further research is aimed at optimizing the repair composition using plasticizing, hydrophobizing, and adhesive additives.
The reasons for the degradation of load-bearing structures and the collapse of buildings made of limestone-shell rock are considered, the main of which is the moisture content of the material due to damage to the plaster layer. Repair and restoration work on the facades of historic buildings should be carried out using special plaster compositions whose properties are consistent with the main material of the structures. Imported general-purpose materials do not take into account the characteristics of limestone materials. An important aspect of creating domestic plaster compositions for repairing the walls of historic limestone-shell rock buildings is to ensure that the vapor permeability of the plaster and the material of the main wall are consistent; it is the mismatch of materials in terms of vapor permeability that causes the cement-based plaster to delaminate from the limestone surface. For a reasonable design of the composition of a special-purpose plaster mixture, objective information about the vapor permeability of the interacting structural layers is required. Based on the analysis of research and publications, the factors that affect the transfer of water vapor in materials are identified. The method of determining the vapor permeability of shell rock and ashlar-cement plaster mixture is the "dry" cup method with the placement of a desiccant in it. Based on the requirement to establish a steady-state diffusion flow of steam in the test sample and taking into account the saturation of the desiccant, the optimal time for conducting vapor permeability measurements was determined in terms of the duration of the experiment. The vapor permeability coefficients of shell rock and the developed repair compositions were experimentally determined. The average vapor permeability coefficient of the proposed plaster compositions exceeds the vapor permeability coefficient of shell rock. The calculation and graphical method shows that when using ash and gypsum cement compositions, there is no probability of condensation in the thickness of the limestone wall.
1 January 2024 in TECHNICAL SCIENCES AND TECHNOLOGIES
У статті обґрунтована доцільність та на основі комплексних досліджень доведена можливість використання зологіпсоцементних сумішей для оштукатурювання стін будівель з вапняку-черепашника при ремонтно-реставраційних роботах. Показано, що водостійкість затверділої суміші є достатньою для її використання на фасадах будівель. Експериментально доведено, що основні властивості пропонованого ремонтно-реставраційного складу – міцність, паропроникність, адгезія, - узгоджені з властивостями черепашника. Подальші дослідження, спрямовані на покра-щення властивостей штукатурної суміші за рахунок введення комплексу хімічних добавок.