Bowen Gao

Bowen Gao

Auto-generated profile, based on publicly available information

Bowen Gao


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 May 2025 in Separations
Verified
Journal Article
Open access
PDF file
QZQidong Zhang
Qidong Zhang
XLXiaoli Li
Xiaoli Li
ZHZhifang Hu
Zhifang Hu
BGBowen Gao
Bowen Gao
CLChen Liu
Chen Liu
Talcose molybdenite resources are abundant but resource utilization is low. The floatation separation of molybdenite (MoS2) and talc is challenging due to their similar natural hydrophobicity and layered structures. This study investigates the surface properties and interaction mechanisms between these minerals to improve their separation efficiency. Density functional theory (DFT) calculations confirm that the basal planes of both minerals are hydrophobic, while their edge surfaces are hydrophilic. Atomic force microscopy (AFM) and DLVO theory reveal that molybdenite and talc particles aggregate in neutral/acidic conditions but disperse in alkaline solutions due to altered surface forces. Floatation experiments demonstrate that pulp pH is the key controlling factor—alkaline conditions (pH > 10) effectively reduce hetero-aggregation, enabling selective molybdenite recovery. These findings provide critical insights into optimizing floatation processes for talcose molybdenite ores, enhancing resource utilization.

8 October 2026 in Materials
Verified
Journal Article
Open access
PDF file
ZHZhifang Hu
Zhifang Hu
BGBowen Gao
Bowen Gao
HJHonglin Jiang
Honglin Jiang
QZQidong Zhang
Qidong Zhang
YYYanxi Yin
Yanxi Yin
In this study, the iodide refining of high-purity vanadium metal was investigated experimentally and by two-dimensional numerical simulations based on the SIMPLE (Semi-Implicit Method for Pressure-Linked Equations) algorithm. The effects of system temperature, K values (characterizing the deposition filament temperature), initial iodine amount, and raw material packing configuration on the deposition rate, crystal morphology, and mass transport were studied in a custom-built iodide apparatus. The experimental results showed that the deposition rate exhibited a bell-shaped dependence on the source temperature. The optimal source temperature and optimal K value were 1123–1173 K and 40–50, respectively, at which the average deposition rate reached its peak. Both the average deposition rate and the average reaction time increased slightly with increasing initial iodine amount, but the increases were limited. Full loading of the raw material yielded crystal rods of uniform size. Vanadium crystal rods with a diameter of approximately 20 mm were obtained after refining. The metallic impurities Fe, Cr, Al, and Si were reduced to 0.025–0.033 wt.%, <0.001 wt.%, <0.001 wt.%, and <0.002 wt.%, respectively, while the interstitial impurities O, C, and N were reduced to <0.01 wt.%, <0.002 wt.%, and <0.002 wt.%, respectively, indicating that iodide refining can effectively reduce the contents of both interstitial and metallic impurities in vanadium metal. Numerical simulation results showed that the mass transport rate decreased monotonically with increasing total pressure, increased with rising temperature owing to the enhanced VI2 partial-pressure difference, and decreased with increasing transport distance. The flow pattern transitioned from pure diffusion/advection at 300 Pa to transitional vortices at 1000 Pa, and finally to fully developed recirculation at 3000 Pa. The simulation results are qualitatively consistent with the experimental observations, providing a theoretical basis for process optimization. To further improve the purity and scale-up potential of the process, it is necessary to conduct more in-depth research, including the development of fully coupled models that incorporate gas-phase dissociation, non-equilibrium surface kinetics, and composition-dependent mixture properties, as well as three-dimensional simulations and reactor material optimization.