In this study, integration of renewable energy sources and Electric Vehicles (EVs) into a micro-grid was modeled and analyzed. The microgrid is divided into four important parts; a diesel generator, acting as the base power generator; a photovoltaic (PV) farm combined with a wind farm, to produce electrical energy; a vehicle to grid (V2G) system installed next to the last part of the microgrid which is the load of the microgrid. The size of the microgrid represents approximately a community of a thousand households during a low consumption day in spring or fall. There are 100 electric vehicles in the base model which means that there is a 1:10 ratio between the cars and the households. This is a possible scenario in a foreseeable future. The continuous increase in their rate in energy production makes micro-grids important. Microgrids can be designed to meet the energy needs of hospitals, universities or charging stations of electric cars, as well as to meet the energy needs of a district, village or industrial site. Charging stations are needed to charge the electric vehicle battery. In this study, the effects of electric vehicles on the microgrid network are analyzed. Electric vehicles have non-linear circuit elements in their structures. Therefore, they are a source of harmonic current in the microgrid. They negatively affect the power quality of the microgrid. The battery in electric vehicles is charged with direct current. The alternating current from the microgrid needs to be converted to direct current.
10 November 2022 in Journal of Computational Electronics
This paper is regarding the design, modeling and simulation for reducing harmonics with passive LLCL filter in off-grid solar system. It is desired that current and voltage waveforms are to be in the sinusoidal form during energy generation from stand-alone solar systems. This condition can be provided by the most important one of the main factors which to determine the quality of electrical energy. Due to the harmonics produced by the non-linear loads, the waveform of the current and voltage is distorted from the sinusoidal form. The passive LLCL filter is designed and analyzed for mitigation of the total harmonic distortion for current (THDI) in the proposed off-grid PV system. The passive LLCL filter is practically installed between solar inverter and non-linear load. Simulation results are in a good compliance with the theoretical analysis. This study describes a design methodology of a LLCL filter for off-grid power system with a comprehensive study of how to mitigate the harmonics in off-grid solar system. The using of a LLCL filter mitigates the THDI that injected by a six pulse rectifier which is used as a non-linear load. The simulation result shows that the reduction of THDI from 89.89% to 3.257%. This paper attempts to show that the using of LLCL filter with a stand-alone solar system can highly improve the power quality of the system.
Photovoltaic (PV) is the conversion of solar energy into DC electrical energy using PV cells. In addition, solar energy is an important renewable energy source. In this study, it is proposed that Thevenin's equivalent PV cell model produces a voltage-current characteristic that is quite representative of the operation of the PV source. Thevenin's elements depend on ambient temperature conditions, so charging is derived and simplified to construct a model that closely predicts and demonstrates adequate PV cell characteristic for different ambient temperature conditions. This method is very useful for estimating the desired performance and also for examining different Maximum Power Point Tracking (MPPT) algorithms. Theoretically, the simulation was supplemented with test data, then used to develop an equivalent Thevenin model in which the resistance is non-linear and voltage dependent. Thevenin's method and variable pitch is to improve the maximum power transfer to the load by increasing the performance of the PV cell. These methods were modeled and studied in a simulation program.
15 December 2021 in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Photovoltaic (PV) cells are semiconductor materials that convert sunlight coming on their surfaces directly into electrical energy. Solar panels can be converted into electrical energy with efficiency between 5% and 20% depending on the structure of the solar cells. There are many factors which affect the PV cells' generation of electrical energy. These factors are such as efficiency of the solar cells, sunshine duration, humidity, dust, solar radiation and temperature. In this article, the effect of temperature on the PV cell current-voltage (I-V) and power- current (P-V) curves were investigated. Low temperatures do not adversely effect on solar cell efficiency, while high temperatures reduce productivity significantly. This study was carried out for 10 (°C), 30 (°C) and 50 (°C) of ambient temperature. The effect of temperature on the P-V and I-V of the PV solar cell analyzed and plotted by Matlab/Simulink software program. The efficiency of a photovoltaic PV cell mainly depends on the ambient temperature, PV cell temperature, solar irradiation intensity and the type of semiconductor materiel which the PV cell is produced. In this study, using the PV cell catalog data, the equivalent circuit of the panel is modeled in Matlab software program and the effects of temperature changes on the PV cell power have been investigated.
The fill factor is used to determine the quality of electricity generated by the photovoltaic cell.. Open circuit voltage in PV cell is the maximum voltage value that the cell can transmit. The analysis of PV cell fill factor and open circuit voltage was carried out with the developed software program. The PV cell is the smallest building block of the PV solar system and produces voltages between 0.5V and 0.7V. It acts as a current source in the equivalent circuit. The amount of radiation hitting the cell determines how much current it produces. The equivalent circuit of an ideal PV cell consists of a diode and a parallel current source. In order to express losses in applications, series and parallel resistance are added to the ideal equivalent circuit of the PV cell. There are many equivalent circuits in the literature for modeling the equivalent circuit of a PV cell. The single diode equivalent circuit is the most widely used model because of its simplicity and ease of analysis. In this study, Newton-Raphson method was used to find the equivalent circuit parameters of a PV cell. Then, the open circuit voltage and fill factor were found with the software program prepared in Matlab and given in Appendix A.