The article presents the development of an animated multimedia presentation for a prototype of a measuring system designed for radiation monitoring of transport and storage containers for radioactive waste. The 3D model of the container was created using the Autodesk Maya software package, utilizing polygonal geometry for modeling. Maya’s FX subsystem was employed to simulate both radiation and the movement of the ropes. Post-production was carried out using the CapCut video editor. The final animation will be used for public relations purposes by IPM and to support the next phase of the joint project: “Development and testing of methods for the non-invasive analysis of the inventory status of transport and storage containers during extended interim storage”.
Dynamic models of NaOH–H2O falling-film absorbers/desorbers are needed for process analysis and future controller design, but time-resolved experimental data for the target system are not yet available. A dynamic segment-resolved model was developed for a horizontal-tube falling-film heat exchanger. Each of the N = 10 segments is described by four coupled ordinary differential equations governing inner fluid temperature, wall temperature, external solution mass flow rate, and NaOH mass fraction. Absorption and desorption are represented within a unified framework using mode-dependent heat-transfer assumptions and thermophysical property data for NaOH–H2O. For absorption, the simulated steady-state concentration change is Δw = 0.105, close to the reference value of Δw = 0.10; the small residual deviation is attributed to the surfactantfree operating condition of the model. For desorption, the simulated NaOH concentration of approximately 0.45 lies within the reference range of 0.44 to 0.49. Energy-balance errors below 0.05% confirm the numerical consistency of the implementation. The model yields steady-state results consistent with reported reference values and provides a physically sound dynamic formulation suitable as a preliminary plant model for future model-based control studies. Its primary current limitation is the absence of time-resolved experimental data for transient validation and parameter identification. A sensitivity analysis confirms that the steady-state results are analytically independent of the PT1 time constant τ , and quantifies the strong dependence on αe and on the number of discretization segments N.
Non-contaminated plastic waste from healthcare facilities is largely non-infectious and rich in recoverable polymers, yet it is routinely incinerated for lack of an automated sorting process suited to the clinical setting. This paper presents a sensor fusion system design and a comparative hyperspectral classification methodology for that stream. Near-infrared hyperspectral imaging, an RGB line-scan camera, and an inductive metal sensor are integrated on a collaborative robot platform, combining polymer-type identification, visual object detection, and metal discrimination in a late-fusion pipeline. Two hyperspectral classification strategies are specified and compared across labeling cost, robustness, interpretability, and stage of system maturity: reference-spectra distance matching, which needs no labeled training data, and supervised machine learning, which gains robustness as the labeled dataset grows. The two are ordered as successive development phases, the first bootstrapping the second. A throughput and spectral analysis establishes the sensor specification required for production line speeds, which the pipeline architecture accommodates without change to the classification methodology. The regulatory scope of the recoverable fraction under German waste legislation is treated as an explicit design input, determining the material classes targeted and the open-set rejection behavior required of the classifiers. Open design parameters and a validation pathway are identified.
This study offers a comprehensive overview of a range of mathematical methods designed to address uncertainties in engineering calculations and assesses their suitability. The focus is on fuzzy set theory, which has proven to be particularly effective and offers a robust solution package for modelling and analyzing uncertainties. Additionally, a detailed model for analyzing the dynamic behavior of the surface temperature of insulating materials under high-voltage arcs is presented, systematically incorporating uncertainties and imprecision. The model is divided into three sub-models: a current-voltage model, a three-cylinder model, and a temperature-heat model. Through Monte Carlo simulations and correlation analyses, the key influencing parameters on surface temperature were identified, with material and heat transfer properties being recognized as particularly significant. The model was validated through cooling experiments by observing the cooldown process after heating, which showed a high degree of agreement with the simulation results. The application of fuzzy set theory for modelling uncertain parameters enabled precise consideration of uncertainties, making the model a reliable basis for predicting surface temperature under various test conditions and for better understanding the behavior of insulating materials under low current high-voltage arcs (DC).
Non-contaminated plastic waste from healthcare facilities is largely non-infectious and rich in recoverable polymers, yet it is routinely incinerated because no automated sorting process suited to the clinical setting has been established. This paper presents the design of a sensor fusion system and a hyperspectral classification methodology for this stream; experimental results are not yet available and will be reported in a follow-up study. Near-infrared hyperspectral imaging, an RGB line-scan camera, and an inductive metal sensor are integrated on a collaborative robot platform and combined in a late-fusion pipeline for polymer identification, object detection, and metal discrimination. Two hyperspectral classification strategies are specified: reference-spectrum distance matching, which requires no labeled training data, and supervised machine learning, which depends on a labeled dataset. A conceptual comparison based on their methodological properties and on published evidence leads to their use as successive development phases, with the first strategy helping to build the training set for the second. An analytical assessment based on sensor datasheet values indicates the sensor specification required for production line speeds, which the pipeline accommodates without changes to the classification methodology. The regulatory scope of the recoverable fraction under German waste legislation is treated as a design input that determines the target material classes and the open-set rejection behavior required of the classifiers. Open design parameters and a staged validation pathway are identified.