Xiaofang Pan

Dr. Xiaofang Pan


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 December 2024 in Materials
Verified
Journal Article
Open access
PDF file
LJLan Jiang
Lan Jiang
XPXiaofang Pan
Xiaofang Pan
ZLZhongkai Li
Zhongkai Li
BYBo Yuan
Bo Yuan
WLWenxin Liu
Wenxin Liu
Jun LiuJun Liu
Jun Liu
Direct energy deposition (DED) technology shows promising applications in the production of roller die cutters. The optimization of process parameters, scanning strategies, and analyses of compressive properties and wear behavior are required prior to application. Therefore, this work investigated the influence of scanning strategy and overlap ratio on the microstructure, microhardness, compressive properties, and wear resistance of M2 high-speed steel (HSS) with DED on a 316 L cylindrical surface. The results reveal that along the deposition direction of the sample, the grain size gradually decreases, with hardness increasing from 187 HV in the matrix to 708 HV. As the overlap ratio increases, the grain size initially rises and then decreases, while hardness first declines and subsequently increases. The cross-scanning strategy effectively enhances the compressive strength by reducing porosity defects. Furthermore, the compressive strength of the samples initially increases with the overlap ratio before experiencing a slight decrease. The M-3 sample with a 50% overlap ratio exhibits the best compressive strength (3904 MPa). The wear rate decreases and then increases with the rising overlap ratio. Therefore, the M-3 sample, prepared using cross-scanning strategies with an overlap ratio of 50%, demonstrates a uniform and dense microstructure, resulting in superior wear resistance, and the wear rate is as low as 8 × 10−6 mm3·N−1·m−1. The current experimental results provide valuable references for the DED of die-cut knives.

21 April 2025 in Materials
Verified
Journal Article
Open access
PDF file
BYBo Yuan
Bo Yuan
WLWenxin Liu
Wenxin Liu
ZWZhen Wang
Zhen Wang
ZLZhongkai Li
Zhongkai Li
XPXiaofang Pan
Xiaofang Pan
Jun LiuJun Liu
Jun Liu
W-Cu composites are widely used in the fields of switch contact materials and electronic packages because of their high hardness, high plasticity, and excellent thermal conductivity, while the traditional W-Cu composite preparation process is often accompanied by problems such as a long production cycle, difficulties in the processing of shaped parts, and difficulties in guaranteeing the uniformity. Therefore, this work developed a chemical plating technique to prepare W-20 wt.% Cu composite powder with a core–shell structure and used this powder as a raw material for powder metallurgy to solve the problem of inhomogeneity in the production of W-Cu composite by the conventional solution infiltration method. Moreover, the work also developed a high-temperature-resistant photosensitive resin, which was used as a raw material to prepare injection molds using photocuring to replace traditional steel molds. Compared to steel molds, which take about a month to prepare, 3D printed plastic molds take only a few hours, greatly reducing the production cycle. At the same time, 3D printing also provides the feasibility of the production of shaped parts. The injection molded blanks were degreased and sintered under different sintering conditions. The results show that the resultant chemically plated W-Cu composite powder has a uniform Cu coating on the surface, and the Cu forms a dense and uniform three-dimensional network in the scanning electron microscope images of each subsequent sintered specimen, while the photocuring-prepared molds were used to prepare the W-Cu shaped parts, which greatly shortened the production cycle. This preparation method enables rapid preparation of tungsten–copper composite-shaped parts with good homogeneity.

16 September 2026 in Materials
Verified
Journal Article
Open access
PDF file
YXYafen Xu
Yafen Xu
SLShuyan Li
Shuyan Li
Jun LiuJun Liu
Jun Liu
ZLZhongkai Li
Zhongkai Li
XPXiaofang Pan
Xiaofang Pan
JWJieyue Wang
Jieyue Wang
Microneedling has found various applications in dermatology recently. However, many problems still need to be solved in the fabrication of high-aspect-ratio polymeric microneedles with good mechanical strength, dimensional accuracy and thermal conductivity for energy-assisted treatments. Herein, a low-shrinkage photocurable resin specifically designed for high-precision additive manufacturing was developed in this work to enable the rapid and reproducible fabrication of ultra-long microneedle arrays through photopolymerisation-based 3D printing. Moreover, an even and uninterrupted layer of silver was added to the surface at room temperature via electroless plating. The resulting microneedle arrays have good structural integrity and high mechanical strength, and the thermal conductivity of them has been increased by a factor of 37 compared to that of uncoated polymeric materials. Mechanical tests showed that the compressive strength was high enough, and simulated skin and ex vivo porcine skin penetration experiments also demonstrated a low insertion force and stable microchannel formation. The in vitro cytotoxicity tests showed good cell compatibility both before and after silver coating. Such work has successfully developed an all-purpose and manufacturable microneedle platform that connects high-precision additive manufacturing with energy-based dermatological therapy, which provided a scalable strategy for expanding the application of polymeric microneedles in medical aesthetics and related clinical fields. The complete route from the digital model to the finished silver-coated array takes about 2.5 h and requires no mould, master or dedicated tooling. The arrays are intended to serve as low-cost, single-use and geometrically customisable needle-electrode cartridges for energy-assisted dermatological treatment and in particular for fractional radiofrequency (RF) microneedling.

11 February 2026 in Materials
Verified
Journal Article
Open access
PDF file
LJLan Jiang
Lan Jiang
ZLZhongkai Li
Zhongkai Li
XPXiaofang Pan
Xiaofang Pan
DLDanya Li
Danya Li
WLWenxin Liu
Wenxin Liu
Jun LiuJun Liu
Jun Liu
Laser-cladding directed energy deposition enables both the repair and fabrication of complex metallic components with curved surfaces. However, during multi-axis deposition on curved substrates, sharp transient feed-rate fluctuations at corner segments—together with an approximately constant powder feed rate—readily cause local over-deposition and geometric defects (e.g., nodules and humps). These defects compromise surface-profile fidelity, thereby creating a major barrier to practical deployment. To overcome this limitation, we propose a corner-oriented path-optimization strategy based on geometric code parsing. By operating directly on the toolpath without modifying the Computer-Aided Design model or slicing workflow, the proposed method suppresses corner overbuild and associated morphological distortion in curved-surface directed energy deposition, substantially improving dimensional consistency and surface quality. Overall, this strategy provides a scalable and broadly applicable route toward high-precision, high-reliability, industrial-scale curved-surface additive manufacturing.