The micro-groove structure on the planar surface has been widely used in the tribology field for improving the lubrication performance, thereby reducing the friction coefficient and wear. However, in the conventional cutting (CC) process, the high-quality, high-precision machining of the micro-groove on titanium alloy has always been a challenge, because considerable problems including poor surface integrity and a high level of the material swelling and springback remain unresolved. In this study, the ultrasonic elliptical vibration assisted cutting (UEVC) technology was employed, which aimed to minimize the level of the material swelling and springback and improve the machining quality. A series of comparative investigations on the surface defect, surface roughness, and material swelling and springback under the CC and UEVC processes were performed. The experimental results certified that the material swelling and springback significantly reduced and the surface integrity obviously improved in the UEVC process in comparison to that in the CC process. Furthermore, for all the predetermined depths of the cut, when the TSR (the ratio of the nominal cutting speed to the peak horizontal vibration speed) was equal to one of twenty four or one of forty eight, the accuracy of the machined micro-groove depth, width and the profile radius reached satisfactorily to 98%, and the roughness values were approximately 0.1 μm. The experimental results demonstrate that the UEVC technology is a feasible method for the high-quality and high-precision processing of the micro-groove on Ti-6Al-4V alloy.

In this paper, a novel single-driven ultrasonic elliptical vibration cutting (SDUEVC) device with a succinct structure and a simple assembly is proposed and investigated. A tailored horn with a tilted-slot structure was employed in the designed SDUEVC device. Also, the elliptical trajectory formation mechanism of the designed SDUEVC device was described by using the theory of mechanical vibration. Furthermore, the finite element method (FEM) was used to optimize the tilted-slot structure parameters and there are four parameters selected as the optimization factors. The results indicated that the proposed SDUEVC device can generate larger vertical amplitude than previous SDUEVC devices, which provides an important and positive effect for the cutting performance of the proposed SDUEVC device. According to the optimized results, a prototype SDUEVC device was fabricated and its vibration characteristic was tested. When the excitation signal voltage was 500 V_p-p, the test results indicated that the amplitudes in the axial and vertical directions were 8.7 μm and 6.8 μm, respectively. Furthermore, an elliptical trajectory was generated at the cutting tool tip. Finally, the proposed SDUEVC device was used to fabricate microdimple patterns as the initial application to confirm the feasibility of the proposed SDUEVC device.

Geometric errors are inevitably introduced into any multiaxis measuring system, and the geometric error is one of the main factors that seriously affects the measurement accuracy. The present work investigates the error distribution of the prototype of a 5-axis measuring machine based on sensitivity analysis of geometric errors. The measurement error modeling of the 5-axis measuring machine is first established via the homogeneous coordinate transformation, and the Sobol global sensitivity analysis method is then employed to quantify the influence of geometric errors on the measurement result with the sensitivity index. The result shows that most of the angular errors are the crucial geometric errors seriously affecting the measurement result. These errors are supposed to be fully considered in the accuracy design and manufacturing stages. The error levels of the crucial geometric errors were distributed and readjusted according to the sensitivity analysis result. Some practical approaches to distribute and improve the crucial geometric errors have been given in detail. The error distribution method is effective to equalize the influence of the crucial geometric errors on the measurement result as possible. The findings of this study provide significant meanings for the optimal design and accurate manufacturing of the 5-axis measuring machine, and the proposed method can be used to improve the measurement accuracy of the 5-axis measuring machine.

In this paper, a novel positioner fixture with a high repeated positioning accuracy and a high stiffness is proposed and investigated. A high-precision end-toothed disc is used to achieve the high repeated positioning accuracy of the designed positioner fixture. The mathematical models of the cumulative error of the tooth pitch, the tooth alignment error and the error of the tooth profile half-angle of the end-toothed disc are analyzed. The allowable tolerance values of the cumulative error of the tooth pitch, the tooth alignment error and the error of the tooth profile half-angle of the end-toothed disc are given. According to the theoretical calculation results, a prototype positioner fixture is fabricated and its repeated positioning accuracy and stiffness are tested. The test results indicate that the stiffness of the proposed positioner fixture is 1050.5 N/μm, which is larger than the previous positioner fixtures of the same type. The repeated positioning accuracy of the proposed positioner fixture in the x, y and z directions are ±0.48 μm, ±0.45 μm and ±0.49 μm, respectively, which is significantly higher than the previous positioner fixtures.