Yang Wang

Dr. Yang Wang


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 September 2023 in Light: Science & Applications
Verified
Journal Article
Open access
PDF file
PLPo Lu
Po Lu
TLTing Li
Ting Li
MLMin Lu
Min Lu
CRCheng Ruan
Cheng Ruan
SSSiqi Sun
Siqi Sun
YZYu Zhang
Yu Zhang
Considering the multi-functionalization of ligands, it is crucial for ligand molecular design to reveal the landscape of anchoring sites. Here, a typical triphenylphosphine (TPP) ligand was employed to explore its effect on the surface of CsPbI3 perovskite nanocrystals (PNCs). Except for the conventionally considered P-Pb coordination, an P-I supramolecular halogen bonding was also found on the NC surface. The coexistence of the above two types of bonding significantly increased the formation energy of iodine vacancy defects and improved the photoluminescence quantum yield of PNCs up to 93%. Meanwhile, the direct interaction of P and I enhanced the stability of the Pb-I octahedra and dramatically inhibited the migration of I ions. Furthermore, the introduction of additional benzene rings (2-(Diphenylphosphino)-biphenyl (DPB)) increased the delocalized properties of the PNC surface and significantly improved the charge transport of the PNCs. As a result, the DPB passivated CsPbI3 NCs based top-emitting LEDs exhibite a peak external quantum efficiency (EQE) of 22.8%, a maximum luminance of 15, 204 cd m−2, and an extremely low-efficiency roll-off of 2.6% at the current density of 500 mA cm−2.

22 September 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
CFCHEN YU FENG
CHEN YU FENG
XZXifeng Zheng
Xifeng Zheng
HCHui Cao
Hui Cao
YWYang Wang
Yang Wang
HCHongbin Cheng
Hongbin Cheng
YCYu Chen
Yu Chen
This paper proposes a Field Programmable Gate Array (FPGA)-based control system to implement micro-light-emitting diode (micro-LED) real-time display. The control system includes the interface control, video processing, memory management, image data transmission, control signal generation and correction. Then, we implement the micro-LED real-time display via memory management. We propose the brightness correction to achieve high grey-scale and high uniformity display. The LEDs are mounted on the glass substrate prepared using low-temperature polysilicon (LTPS) technology, and then we find the 24 × 46 pixels micro-LED panel. And the control system has been successfully applied to the panel of glass-based micro-LED displays. A new grey control method is proposed in this work, which can effectively improve the refresh rate of the micro-LED displays. The high grey-scale refresh rate is 2100 Hz, and the low grey-scale refresh rate is 300 Hz. The uniformity of the panel is increased to 85% after brightness correction.

24 August 2024 in Electronics
Verified
Journal Article
Open access
PDF file
CFCHEN YU FENG
CHEN YU FENG
XZXifeng Zheng
Xifeng Zheng
XMXinyue Mao
Xinyue Mao
HCHui Cao
Hui Cao
YWYang Wang
Yang Wang
YCYu Chen
Yu Chen
This paper presents the design of a 40 × 40 micro-light-emitting (micro-LED) test array based on a 20 mm × 20 mm substrate. A study of the relationship between luminous brightness, driving current, and driving voltage revealed that the data voltages of the red, green, and blue micro-LED array from 0 to 255 grey levels are 0.31 V, 0.29 V, and 0.30 V, respectively, under the condition that the target brightness of the white field is 1000 nits and the color temperature is 9300 K. The brightness range of the red micro-LED array is 64.8–101.2%, the brightness range of the green micro-LED array is 66.5–102.8%, and the brightness range of the blue micro-LED array is 53.5–129.2%. In order to overcome the luminance nonuniformity, a grey level depth of 12 -bit is required. A 10T3C pixel driver circuit based on low-temperature polysilicon (LTPS) with a depth of 12 bits greyscale is designed and fabricated into the micro-LED display. A brightness uniformity of 84.1–97.1% can be achieved by brightness correction combined with a 12-bit greyscale depth system for micro-LED display. This provides a valuable reference point for subsequent improvements in the quality of micro-LED displays.

6 November 2026 in Electronics
Verified
Journal Article
Open access
PDF file
YJYu Jinhuan
Yu Jinhuan
XZXifeng Zheng
Xifeng Zheng
RZRan Zhan
Ran Zhan
CFCHEN YU FENG
CHEN YU FENG
YWYang Wang
Yang Wang
XMXinyue Mao
Xinyue Mao
RGB channel response differences and model prediction bias limit joint grayscale luminance and chromaticity calibration in passive-matrix (PM) Mini-LED displays. A method combining local response modeling and output residual correction is therefore proposed. A forward model constructed from single-channel and equal-RGB-code responses is used to optimize a baseline compensation mapping allowing separate RGB drive-code adjustments. At five baseline compensation operating points, residuals are calculated as the differences between simulated outputs and model predictions evaluated at the same RGB triplet. These residuals are interpolated along the gray-level axis to update luminance and chromaticity predictions before reoptimizing the mapping. Numerical evaluation based on measured base-response data shows that, over 250 gray levels excluded from residual sampling in the original scenario, joint correction reduces the mean full-scale-normalized absolute luminance error from 0.2885% to 0.1028% and the mean chromaticity deviation Δu′v′ from 0.002823 to 0.001126 relative to the baseline mapping. Compared with residual correction using existing equal-RGB-code responses, these metrics decrease by a further 20.1% and 8.1%, respectively. Both advantages persist across 30 numerical recalibration runs in the original scenario. However, in scenario S1 with stronger candidate-code-dependent deviations, joint correction produces a higher mean luminance error than the baseline, while retaining a lower mean chromaticity deviation. The results indicate that sparse residual feedback can improve calibration at unsampled gray levels when sampled residuals adequately represent prediction bias within the candidate domain. Independent measurements at non-equal RGB triplets are still needed to validate physical calibration performance.