Based on the embedded atomic method potential energy function, the uniaxial tensile and compressive deformation of nanocrystalline Al with different sizes in the crystal orientation ⟨100⟩ is studied by the atomistic molecular dynamics simulation approach at six different temperatures and three different strain rates. The simulation results show that, under the same simulation condition, the stress–strain curves of nanocrystalline Al in the process of uniaxial tension and compression are asymmetric and there exists a significant difference in the late region of elastic deformation. The reason for the asymmetry lies in the difference in the process that the work done by the surroundings converts into the strain energy of nanocrystalline Al in the deformation process. At the same temperature and strain rate, the tensile elastic modulus and yield strength of nanocrystalline Al are greater than those of compression. With the increase in temperature, the elastic modulus and yield strength of tension and compression gradually decrease and the two values tend to be the same with the increase in temperature. The higher the strain rate, the greater the yield strength and the corresponding yield strain of the nanocrystalline Al. Finally, the effects of size on the tensile and compressive properties of nanocrystalline Al are briefly discussed.
18 February 2022 in Journal of Materials Chemistry C
Lanthanide-doped upconversion nanoparticles (UCNPs) can be used as nanoscale thermometers and have recently attracted great attention. However, due to their intrinsically low quantum yield and remarkable intensity attenuation with increasing temperature, simultaneous improvement of their fluorescence intensity, thermometric sensitivity and signal to noise ratio (SNR) is still a challenge. In this work, we have proposed a 2D photonic crystal (PC)/Au/UCNPs upconverted platform and investigated its optical properties and thermal response. The excitation field can be highly localized by the all-dielectric optical concentration and plasmonic hot carrier, which can not only enhance the detecting signal intensity and the SNR but also increase the thermometric sensitivity by creating extra amplified interfacial thermal fields around the UCNPs, which is also known as the thermal self-amplification effect. Compared with traditional UCNPs, the fluorescence intensity, thermometric sensitivity and SNR of the proposed upconverted platform are enhanced by over 1500%, 30% and 3000%, respectively. This study presents a route for enhancing the comprehensive performance of upconversion thermometers via optical field localization.
Thermal-induced self-degradation and recombination losses greatly impact the performance of inverted perovskite solar cells (PSCs). Herein, a multi-functional thermal management strategy based on ionic liquids (1-butyl-3-methylimidazole dibutyl phosphate, BMDP) is proposed for the first time to overcome these challenges for excellent thermal stability and efficiency in inverted PSCs. The BMDP can diffuse into grain boundaries (GBs) and stay at the surface perovskite film, resulting in efficient thermal management, trap passivation, ion migration elimination, hydrophobic improvement, as well as interface electric field enhancement. With the help of BMDP, the thermal conductivity of the perovskite film and the device at high temperatures were enhanced by 32.56% and 61.90%, respectively. In addition, the heat dissipation speed device was also accelerated. The power conversion efficiency (PCE) of the unencapsulated devices based on the intrinsically unstable MAPbI3/PCBM heterojunction can maintain about 90% of the initial value, whether at 85 °C for 1080 h, or in air (RH = 30 ± 5%, 25 °C) for 1440 h, which is one of the most reported stable results based on the thermally unstable MAPbI3/PCBM heterojunction to date. Furthermore, the high PCE can be improved greatly with this multi-functional thermal management, and the highest PCE of 21.98% and 23.25% have been achieved in the inverted devices based on MA/I and Rb/Cs/FA/MA/I/Br perovskite systems.
20 April 2018 in IEEE Journal of Selected Topics in Quantum Electronics
In this paper, we theoretically and numerically reported a simple plasmonic sensor design for the accurate detection of refractive index(RI). The sensing property was characterized by a derived theoretical model, which demonstrated the accurate sensing by measuring the intensity of a fixed narrow passband. It was found that the coupling phase modulation caused by the analyte was the main mechanism of the plasmonic sensing. The advantage of this sensor design was that the sensing response band(or resonance wavelength) was fixed and narrow, even when the RI of analyte increases. Thus an optical detector with certain working wavelength range can be used to detect wide range of RI, this was also confirmed by a two times narrower range than the common used approach in detecting the same analyte. The specific sensor design and the results may provide some guidance for the integrated plasmonic sensor design and make the sensor more flexible in RI detecting.