The adsorption of Ni, Co, Mn, Ti, and Zr at the -reconstructed surface was studied by scanning tunneling microscopy, x-ray and ultraviolet photoelectron spectroscopy, low-energy electron diffraction (LEED), and density functional theory (DFT). Following deposition at room temperature, metals are either adsorbed as isolated adatoms or fill the subsurface cation vacancy sites responsible for the reconstruction. Both configurations coexist, but the ratio of adatoms to incorporated atoms depends on the metal; Ni prefers the adatom configuration, Co and Mn form adatoms and incorporated atoms in similar numbers, and Ti and Zr are almost fully incorporated. With mild annealing, all adatoms transition to the incorporated cation configuration. At high coverage, the reconstruction is lifted because all subsurface cation vacancies become occupied with metal atoms, and a LEED pattern is observed. DFT+U calculations for the extreme cases, Ni and Ti, confirm the energetic preference for incorporation, with calculated oxidation states in good agreement with photoemission experiments. Because the site preference is analogous to bulk ferrite compounds, similar behavior is likely to be typical for elements forming a solid solution with .
26 August 2015 in The Journal of Physical Chemistry C
The adsorption of CO2 on the Fe3O4(001)-( × )R45° surface was studied experimentally using temperature programmed desorption (TPD), photoelectron spectroscopies (UPS and XPS), and scanning tunneling microscopy. CO2 binds most strongly at defects related to Fe2+, including antiphase domain boundaries in the surface reconstruction and above incorporated Fe interstitials. At higher coverages,CO2 adsorbs at fivefold-coordinated Fe3+ sites with a binding energy of 0.4 eV. Above a coverage of 4 molecules per ( × )R45° unit cell, further adsorption results in a compression of the first monolayer up to a density approaching that of a CO2 ice layer. Surprisingly, desorption of the second monolayer occurs at a lower temperature (≈84 K) than CO2 multilayers (≈88 K), suggestive of a metastable phase or diffusion-limited island growth. The paper also discusses design considerations for a vacuum system optimized to study the surface chemistry of metal oxide single crystals, including the calibration and characterisation of a molecular beam source for quantitative TPD measurements.
The atomic-scale mechanisms underlying the growth of Ag on the (√2×√2)R45°-Fe3O4(001) surface were studied using scanning tunneling microscopy and density functional theory based calculations. For coverages up to 0.5 ML, Ag adatoms populate the surface exclusively; agglomeration into nanoparticles occurs only with the lifting of the reconstruction at 720 K. Above 0.5 ML, Ag clusters nucleate spontaneously and grow at the expense of the surrounding material with mild annealing. This unusual behavior results from a kinetic barrier associated with the (√2×√2)R45° reconstruction, which prevents adatoms from transitioning to the thermodynamically favorable 3D phase. The barrier is identified as the large separation between stable adsorption sites, which prevents homogeneous cluster nucleation and the instability of the Ag dimer against decay to two adatoms. Since the system is dominated by kinetics as long as the (√2×√2)R45° reconstruction exists, the growth is not well described by the traditional growth modes. It can be understood, however, as the result of supersaturation within an adsorption template system.
The adsorption of methanol (CH3OH) at the Fe3O4(001)−(√2 × √2)R45° surface was studied using X-ray photoelectron spectroscopy, scanning tunneling microscopy, and temperature-programmed desorption (TPD). CH3OH adsorbs exclusively at surface defect sites at room temperature to form hydroxyl groups and methoxy (CH3O) species. Active sites are identified as step edges, iron adatoms, antiphase domain boundaries in the (√2 × √2)R45° reconstruction, and above Fe atoms incorporated in the subsurface. In TPD, recombinative desorption is observed around 300 K, and a disproportionation reaction to form methanol and formaldehyde occurs at 470 K.