Ermano De Almeida

Mr. Ermano De Almeida

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
EAErmano De Almeida
Ermano De Almeida
MGMarcel Van Gent
Marcel Van Gent
Bas HoflandBas Hofland
Bas Hofland
In order to design reliable coastal structures, for present and future scenarios, universal and precise damage assessment methods are required. This study addresses this need, and presents improved damage characterization methods for coastal structures with rock armored slopes. The data used in this study were obtained from a test campaign carried out at Deltares within the European Union (EU) Hydralab+ framework. During these tests, advanced measuring techniques (digital stereo photography) were used, which are able to survey the full extension of the structure and identify local variations of damage. The damage characterization method proposed here is based on three fundamental aspects: clear damage concepts, precise damage parameters, and high resolution measuring techniques. Regarding damage concepts, first, the importance of the characterization width is studied. For damage parameters obtained from the maximum erosion depth observed in a given width (E3D,m), the measured damage increases continuously with increased characterization width. However, for damage parameters obtained from width-averaged profiles (S and E2D), the measured damage reduces with increased characterization width. Second, a new definition of damage limits (damage initiation, intermediate damage, and failure) is presented and calibrated. Regarding the damage parameters, the parameter E3D,5, which describes the maximum erosion depth within the characterization width, is recommended as a robust damage parameter for conventional and non-conventional configurations based on four main characteristics: its low bias, its low random error, the ability to distinguish damage levels, and its validity and suitability for all types of structures (conventional and non-conventional). In addition, the results from this study show that the damage measured with the damage parameter E3D,5 presents an extreme value distribution.

Verified
Journal Article
Open access
PDF file
MGMarcel Van Gent
Marcel Van Gent
EAErmano De Almeida
Ermano De Almeida
Bas HoflandBas Hofland
Bas Hofland
Physical model tests were performed in a wave flume at Deltares with rock armoured slopes. A shallow foreshore was present. At deep water, the same wave conditions were used, but by applying different water levels, the wave loading on the rock armoured slopes increased considerably with increasing water levels. This allowed an assessment of the effects of sea level rise. Damage was measured by using digital stereo photography (DSP), which provides information on each individual stone that is displaced. Two test series were performed five times. This allowed for a statistical analysis of the damage to rock armoured slopes, which is uncommon due to the absence of statistical information based on a systematic repetition of test series. The statistical analysis demonstrates the need for taking the mean damage into account in the design of rock armoured slopes. This is important in addition to characterising the damage itself by erosion areas and erosion depths. The relation between damage parameters, such as the erosion area and erosion depth, was obtained from the tests. Besides tests with a straight slope, tests with a berm in the seaward slopes were also performed. A new method to take the so-called length effect into account is proposed to extrapolate results from physical model tests to real structures. This length effect is important, but is normally overlooked in the design of rubble mound structures. Standard deviations based on the presented model tests were used.

Verified
Journal Article
Open access
PDF file
EAErmano De Almeida
Ermano De Almeida
Bas HoflandBas Hofland
Bas Hofland
This study focusses on increasing the understanding on vertical hydraulic structures with relatively short overhangs subjected to standing wave impacts. To this end, the impact velocity and the entrapped air are studied in detail, given their influence on the impulsive loading characteristics and consequently on the structural dynamic response. This study is based on regular wave laboratory experimental data obtained for relatively short overhangs with respect to the wave length and with respect to the overhang height. The laboratory tests illustrate the complex wave hydrodynamics before the wave impacts, influenced by the incident wave conditions and structural characteristics. Regarding the impact velocity, the experimental measurements with a wall wave gauge in the tests without overhangs show that the maximum upward velocities deviate from linear wave theory between +5.5% and +13.0%, while the zero-crossing upward velocities deviate from linear wave theory between +1.9% and +7.0%. The zero-crossing upward velocities estimated from third order wave theory deviate from the linear wave theory between +1.8% and +4.7%. In the tests with overhangs, the maximum upward velocity below the overhang estimated by camera recording measurements deviates from linear wave theory between −11.8% and +13.4%. It was also found that when considering the experimental impact velocity from camera recordings in the tests with overhangs, the mean effective bounce-back factor β deviates relatively little from when linear wave theory is used (≈1%), while the uncertainty described by the standard deviation increases significantly (≈35%). Regarding the entrapped air, it is shown that the interaction between incident wave parameters and structural configurations leads to a large variation in the entrapped air area, up to a factor of 5.7 for shorter overhangs and a factor of 9.5 for longer overhangs. This variability in entrapped air characteristics leads to significant effects on the loading on the structure, as observed by the variability on pressure measurements. The experimental results showed increasing impact durations and increasing effective bounce-back factor β in the tests with increasing entrapped air dimensions. This study highlights the importance of the details of the impact velocity and entrapped air for load estimations during the design of vertical hydraulic structures exposed to standing wave impacts. This is particularly important for thin structures such as steel gates which are susceptible to a dynamic behaviour under such impulsive loads.

1 September 2023 in Coastal Engineering Proceedings
Verified
Journal Article
Open access
PDF file
Alessandro AntoniniAlessandro Antonini
Alessandro Antonini
DDDimitrios Dermentzoglou
Dimitrios Dermentzoglou
EAErmano De Almeida
Ermano De Almeida
Bas HoflandBas Hofland
Bas Hofland
Daniele CelliDaniele Celli
Daniele Celli
Paolo De GirolamoPaolo De Girolamo
Paolo De Girolamo
The use of sea-wall and storm-wall structures within valuable landscape or urban areas often imposes rather restrictive limits in terms of structures height. A viable solution to address the safety against overtopping and the architectonical requirements is the use of recurved parapets. However, this type of structure is exposed to large impulsive loads that have been recently described and named as confined-crest impact, (C-CI), (Castellino et al., 2018) and caused several failures such as those in Strand (South Africa), Pico Island (Portugal) and Civitavecchia (Italy), (Castellino et al., 2021; Dermentzoglou et al., 2020; Martinelli et al., 2018). Accordingly, tools to properly design these curvilinear structures and to carry out comparative assessments between the induced advantage in terms of overtopping and increased structural complexity due to its shape and the C-CI are required. This work aims to identify practical design tools and provide benchmark data for the validation of the CFD model presented in the abstract n. 1643: “Castellino et al., Numerical experiments on overhanging parapets under non-breaking wave conditions”. A series of non-breaking regular and irregular waves experiments have been performed at the TU Delft Hydraulic Engineering Laboratory to investigate the contrasting behaviour of the overtopping phenomena and the exerted impulsive wave load on recurved parapets.