Antonio Carlos Valdiero

Dr. Antonio Carlos Valdiero

orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2011 in Mathematical Problems in Engineering
Verified
Journal Article
Open access
PDF file
AVAntonio Carlos Valdiero
Antonio Carlos Valdiero
CRCarla Silvane Ritter
Carla Silvane Ritter
CRCláudio Fernando Rios
Cláudio Fernando Rios
MRMarat Rafikov
Marat Rafikov
This paper addresses a new methodology for servo pneumatic actuators mathematical modeling and selection from the dynamic behavior study in engineering applications. The pneumatic actuator is very common in industrial application because it has the following advantages: its maintenance is easy and simple, with relatively low cost, self‐cooling properties, good power density (power/dimension rate), fast acting with high accelerations, and installation flexibility. The proposed fifth‐order nonlinear mathematical model represents the main characteristics of this nonlinear dynamic system, as servo valve dead zone, air flow‐pressure relationship through valve orifice, air compressibility, and friction effects between contact surfaces in actuator seals. Simulation results show the dynamic performance for different pneumatic cylinders in order to see which features contribute to a better behavior of the system. The knowledge of this behavior allows an appropriate choice of pneumatic actuator, mainly contributing to the success of their precise control in several applications.

26 November 2015 in African Journal of Agricultural Research
Verified
Journal Article
Open access
PDF file
GEGhisleni Arenhardt Emilio
Ghisleni Arenhardt Emilio
AJAntonio Gonzalez da Silva Jose
Antonio Gonzalez da Silva Jose
GEGewehr Ewerton
Gewehr Ewerton
Antonio Costa De OliveiraAntonio Costa De Oliveira
Antonio Costa De Oliveira
OMOsorio Binelo Manuel
Osorio Binelo Manuel
AEAntonio Gonzalez da Silva Jos Eacute
Antonio Gonzalez da Silva Jos Eacute
High wheat yields, besides the genetic potential and edaphoclimatic conditions, are obtained by proper management and nitrogen use. The objective of the study was to define the most appropriate time for N-fertilizer application, considering the range of greatest wheat requirements, dependent on the succession system type and the predictability of favorable and unfavorable years. The study was carried out in the 2008 to 2012 years, in Augusto Pestana, Rio Grande do Sul, Brazil. The experimental design was randomized blocks with four replications, with N-fertilizer application at 0, 10, 30 and 60 days after emergence, considering the corn/wheat and soybean/wheat succession system. The study found that the best time for nitrogen fertilizer application on wheat is mostly influenced by the year of cultivation and is less influenced by the succession system type. The appropriate time for the N-fertilizer application in favorable years of cultivation was about 45 days after emergence. In unfavorable years, it must be anticipated. Regardless of the cultivation year and the succession system type, the N-fertilization at 30 days after emergence evidenced the highest means as the most stabile grain yield. Key words: Wheat Triticum aestivum, N-fertilizer time, optimization.

1 March 2006 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Open access
PDF file
RGRaul Guenther
Raul Guenther
EPEduardo A. Perondi
Eduardo A. Perondi
EDEdson R. DePieri
Edson R. DePieri
AVAntonio Carlos Valdiero
Antonio Carlos Valdiero
This paper proposes a cascade controller with friction compensation based on the LuGre model. This control is applied to a pneumatic positioning system. The cascade methodology consists of dividing the pneumatic positioning system model into two subsystems: a mechanical subsystem and a pneumatic subsystem. This division allows the introduction of friction compensation at force level in the pneumatic positioning system. Using Lyapunov's direct method, the convergence of the tracking errors is shown under the assumption that the system parameters are known. Experimental results illustrate the main characteristics of the proposed controller.

1 January 2008 in International Journal of Fluid Power
Verified
Journal Article
Closed access
AVAntonio Carlos Valdiero
Antonio Carlos Valdiero
DBDelair Bavaresco
Delair Bavaresco
PAPedro Luís Andrighetto
Pedro Luís Andrighetto
This work presents a new methodology for dead zone nonlinearity identification in proportional directional pneumatic valves. It is based on observing the dynamic behaviour of the pressure in the valve gaps. Dead zone is common in hydraulic and pneumatic valves because the spool blocks valve orifices with some overlap, so that for a range of spool positions there is no fluid flow. The dead zone nonlinearity is a key factor that limits both static and dynamic performance in feedback control of fluid power systems. The usual method to cancel the harmful effects of dead zone is to add its fixed inverse function into the controller. This inverse is modelled by a set of parameters that need to be identified. The classic dead zone parameter identification uses expensive flow transducers and special test rig, while our proposed methodology needs only pressure transducers. Experimental results illustrate the efficacy of this methodology that is cheaper and faster.

1 June 2019
Verified
Conference Paper
Closed access
RGR. Goergen
R. Goergen
AVAntonio Carlos Valdiero
Antonio Carlos Valdiero
Luiz Antonio RasiaLuiz Antonio Rasia
Luiz Antonio Rasia
MOM. Oberdorfer
M. Oberdorfer
JSJ. P. de Souza
J. P. de Souza
RGR. S. Goncalves
R. S. Goncalves
Nowadays, many people suffer from physical disabilities caused by illness or accidents. The problems in the lower limb are one of the main that interrupt the activities of daily life of these people. To assist them in the activities of daily living, many support devices for upper and lower limb movement have been developed. In this paper is proposed a new simple and low-cost pneumatic robotic mechanism for lower limb rehabilitation. We employ a pneumatic actuator so that it is possible to obtain safety for the operation and the control of the force by the appropriate regulation of the pressures in the pneumatic cylinder chambers of the robot for rehabilitation. This work deals with the development of the robot for rehabilitation from a methodology of integration of mathematical modeling with the phases of the design process. It is concluded that the results obtained are a modular design that can be improved for multiple degrees of freedom and adapted also for rehabilitation of upper limbs.

1 January 2018
Verified
Conference Paper
Closed access
PDF file
Luiz Antonio RasiaLuiz Antonio Rasia
Luiz Antonio Rasia
PPPatricia Carolina Pedrali
Patricia Carolina Pedrali
AVAntonio Carlos Valdiero
Antonio Carlos Valdiero