Results of comparison between drag coefficients established by the firing tests and numerical simulations are presented in the paper. The results of numerical calculations carried out by CFD method, exploiting Ansys Fluent v16 software, were used to develop initial firing tables for newly designed projectiles for RAK mortar.
The paper presents simulation of flight path of a lead ball fired with an arquebus and its penetration process through an armor of heavy cavalry knights of the beginning of the 16th century used during the Battle of Pavia on 24 February, 1525. The mass use of firearms by the footmen against the cavalry decided the result of the battle and started a large deployment of infantry formations armed in firearms. The basic ballistic characteristics of 16th century arquebus necessary for the simulation process are based on historical information. The numerical calculations were used to identify the flying characteristics of the lead ball at the distances securing the penetration of that time horseman’s armour. Penetration capacity of the lead ball through the 16th age horseman armour was estimated by using the finite element method (AUTODYN).
The aim of “Crawfish – Ammunition” project is to develop supersonic mortar projectile for “Crawfish” (“RAK”) self-propelled mortar. This projectile has been developing in Military Institute of Armament Technology. As a main goal of HE projectile is to achieve range above 10000 m, that implicate muzzle velocity according to 500 m/s. Nowadays literature about this kind of projectiles is very poor. In the article authors showed results of exterior ballistic analysis for several types of supersonic mortar projectiles. Analysis was made according to experimental data and numerical calculations. Experimental data was collected on maximum range shooting tests at 500 m/s velocity with 45 degrees elevation. In flight projectile was observed by radar to measure their position and velocity and to gain the data enabled to calculate drag laws for different shape supersonic mortar projectile and quality of projectile stability. Second part of article consists of the CFD numerical analysis of these projectiles. Using Ansys Fluent program authors calculated drag coefficients of these projectiles. Authors estimated the accuracy of CFD method comparing numerical and experimental data. After that they checked drag coefficients of different parts of projectiles (primer, ogive, fins etc.). Analysis of radar data showed drag fluctuations at low velocities of flight (0.5 – 0.8 Ma). CFD method was used to calculate center of force and stability moments. Drag coefficients at different yaw angles was also estimated. That data was used to model yaw of projectiles to compare with experimental data. Finally authors formulated conclusion about accuracy and possibilities of using CFD methods in exterior ballistic.
Basic models applied for analysing and modelling the flight parameters of projectiles were disscussed in the article. A modified model with five degrees of freedom and neglection of the sixth one, representing the projectile rotation speed, is proposed by authors on the basis of conducted analysis to analyse flight parameters of a supersonic mortar projectile. To obtain the coefficients required in the modified model the CFD methods (ANSYS FLUENT software) were used.
In the article, issues concerning the potential use of practice ammunition in the 120 mm self-propelled mortar RAK are described. The basic requirements to be met for this type of ammunition to be used in the RAK mortar, resulting both from the mortar's design and the conditions of the training process, are presented. Next, the main types of practice ammunition and their possible use in the RAK mortar are described. The last paragraph describes the development of a new practice mortar cartridge in the Military Armament Technical Institute and the proposal for a new practice cartridge adapted to the 120 mm RAK mortar was presented.
The paper presents a detailed review of designs of chosen HE ammunition for battle tank guns, taking into account used types of explosives and principle of operation. An analysis of the effectiveness of the ammunition was also carried out, taking into account their ability to fragmentation and production of blast waves, which are crucial in the context of impacting the living force. The work describes not only the technical aspects of ammunition, but presents the results of theoretical calculations, as well, allowing for estimation of danger zones resulting from the use of particular warheads. This makes it possible to understand how different types of ammunition can be optimally used depending on target characteristics and battlefield conditions. Summing it up, the work was aimed to deepen knowledge about modern combat vehicle ammunition, its combat capabilities and applications in the context of current military doctrines. Conclusions from the conducted analyzes can be a basis for further researches on optimization of ammunition and increasing its effectiveness in combat operations.