Andrea Carloni

Dr. Andrea Carloni

Dipartimento Ingegneria dell'Informazione, Università di Pisa
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 December 2018 in Electronics
Verified
Journal Article
Open access
PDF file
Andrea CarloniAndrea Carloni
Andrea Carloni
Federico BarontiFederico Baronti
Federico Baronti
Roberto Di RienzoRoberto Di Rienzo
Roberto Di Rienzo
RRRoberto Roncella
Roberto Roncella
Roberto SalettiRoberto Saletti
Roberto Saletti
Technology improvements and cost reduction allow electrochemical energy storage systems based on Lithium-ion cells to massively be used in medium-power applications, where the low system cost is the major constraint. Battery pack maintenance services are expected to be required more often in the future. For this reason, a low-cost instrumentation able to characterize the cells of a battery pack is needed. Several works use low-cost programmable units as Li-ion cell tester, but they are generally based on proprietary-software running on a personal computer. This work introduces an open-source software architecture based on Python language to control common low-cost commercial laboratory instruments. The Python software application is executed on a Raspberry Pi board, which represents the control block of the hardware architecture, instead of a personal computer. The good results obtained during the validation process demonstrate that the proposed cell station tester features measurement accuracy and precision suitable for the characterization of Li-ion cells. Finally, as a simple example of application, the state of health of twenty 40 Ah LiFePO4 cells belonging to a battery pack used in an E-scooter was successfully determined.

13 August 2021 in Energies
Verified
Journal Article
Open access
PDF file
Andrea CarloniAndrea Carloni
Andrea Carloni
Federico BarontiFederico Baronti
Federico Baronti
Roberto Di RienzoRoberto Di Rienzo
Roberto Di Rienzo
RRRoberto Roncella
Roberto Roncella
Roberto SalettiRoberto Saletti
Roberto Saletti
The large increment expected in the diffusion of light-electric-vehicles will raise several issues that must be addressed to cope with this trend, including battery diagnostic and maintenance services. The battery system is the most expensive part in the majority of the e-mobility devices. Therefore, battery manufacturers tend to reduce the battery cost by using simple battery management systems that provide only basic safety features. Possible advanced functionalities are not implemented and the battery may lose performanceduring its use. Widely spread maintenance centers are thus required to support the mobility electrification process, but their diffusion is limited by the high cost ofprofessional battery characterization instruments. This work proposes an open-hardware low-cost battery maintenance tool architecture that can be used with common laboratory instruments. The tool is based on a relay-matrix and a battery monitor integrated circuit. It is able to completely characterize and optimize the state of a battery independently of the battery management system and also gives a figure of the individual aging of the battery cells. The work shows the architecture and the experimental validation of a 16-cells battery maintenance tool prototype. The results demonstrate that utilizing the tool brings the battery in the best possible state and identifies the degradation of the cells in terms of capacity and resistance.

21 March 2020
Verified
Book Chapter
Closed access
PDF file
Andrea CarloniAndrea Carloni
Andrea Carloni
FBFederico Baronti
Federico Baronti
Roberto Di RienzoRoberto Di Rienzo
Roberto Di Rienzo
RRRoberto Roncella
Roberto Roncella
Roberto SalettiRoberto Saletti
Roberto Saletti

31 January 2021 in Energies
Verified
Journal Article
Open access
PDF file
Andrea CarloniAndrea Carloni
Andrea Carloni
Federico BarontiFederico Baronti
Federico Baronti
Roberto Di RienzoRoberto Di Rienzo
Roberto Di Rienzo
RRRoberto Roncella
Roberto Roncella
Roberto SalettiRoberto Saletti
Roberto Saletti
Wireless inductive-coupled power transfer is a very appealing technique for the battery recharge of autonomous devices like surveillance drones. The charger design mainly focuses on lightness and fast-charging to improve the drone mission times and reduce the no-flight gaps. The charger secondary circuit mounted on the drone generally consists of a full-bridge rectifier and a second-order filter. The filter cut-off frequency is usually chosen to make the rectifier output voltage constant and so that the battery is charged with continuous quantities. Previous works showed that an increase in power transfer is achieved, if compared to the traditional case, when the second-order filter resonant frequency is close to the double of the wireless charger excitation and the filter works in resonance. This work demonstrates that the condition of resonance is necessary but not sufficient to achieve the power increment. The bridge rectifier diodes must work in discontinuous-mode to improve the power transfer. The paper also investigates the dependence of the power transfer increase on the wireless excitation frequency. It is found the minimum frequency value below which the power transfer gain is not possible. This frequency transition point is calculated, and it is shown that the gain in power transfer is obtained for any battery when its equivalent circuit parameters are known. LTSpice simulations demonstrate that the transferred power can be incremented of around 30%, if compared to the case in which the rectifier works in continuous mode. This achievement is obtained by following the design recommendations proposed at the end of the paper, which trade off the gain in power transfer and the amplitude of the oscillating components of the wireless charger output.

21 May 2020 in Energies
Verified
Journal Article
Open access
PDF file
Andrea CarloniAndrea Carloni
Andrea Carloni
Federico BarontiFederico Baronti
Federico Baronti
Roberto Di RienzoRoberto Di Rienzo
Roberto Di Rienzo
RRRoberto Roncella
Roberto Roncella
Roberto SalettiRoberto Saletti
Roberto Saletti
Wireless inductive-coupled power transfer and opportunity battery charging are very appealing techniques in drone applications. Weight and size are very critical constraints in drones, so the battery and the on-board electronics must be as light and small as possible. The on-board components involved in the resonant inductive-coupled wireless power transfer usually consist of the secondary coil, the compensation capacitor, the bridge rectifier, the LC-filter and the battery. This paper suggests a sizing of the LC-filter capacitor that improves the charging power of the battery. In addition, further on-board space and size is saved by using the stray inductance of the battery as filtering inductor. LTSpice simulations and experimental tests carried out on the prototype of a wireless power transfer circuit shows the dependency of the power delivered to the battery on the filter capacitor size. Finally, it is found that the power transfer to the battery is maximized by choosing the capacitor value that sets the LC-filter resonant frequency close to the double of the excitation frequency of the wireless charging. The drawback is a large current and voltage ripple in the battery.

1 September 2020
Verified
Conference Paper
Closed access
Andrea CarloniAndrea Carloni
Andrea Carloni
Roberto Di RienzoRoberto Di Rienzo
Roberto Di Rienzo
FBFederico Baronti
Federico Baronti
RRRoberto Roncella
Roberto Roncella
Roberto SalettiRoberto Saletti
Roberto Saletti
Resonant inductive coupled wireless power transfer systems are mainly implemented as opportunity charging stations in many applications, such as drones. The estimation of the load equivalent resistance seen before the bridge rectifier in the secondary circuit is crucial for the optimal design of this kind of systems. Generally, the equivalent load resistance model assumes the LC-filter capacitor large enough to neglect the ripple component of the current that flows into the battery. This paper investigates if the above assumption is still correct when the designer chooses a smaller value of the output capacitor, in order to maximize the power transfer at the expense of a nonoptimal efficiency and a larger ripple in the battery voltage and current. The load equivalent resistance was calculated by means of LTSpice simulations in this specific case. The results are compared to those obtained by the typical model generally used in the literature. They show that the development of a new analytical model to extract the load equivalent resistance is required to justify the large difference found.