The amino-functionalized nanosilica/polymer hybrid systems have better salt tolerance and EOR performance than unmodified nanosilica polymer hybrid systems.

As most offshore oilfields come to the middle- and late-exploitation period, and with the popularization of tertiary enhanced oil recovery (EOR) technology, the physical properties of produced fluids become more complex, bringing new challenges to oil-water separation. Conventional solutions, such as increasing the input of chemicals, enlarging the volume of the separator equipment, and extending the processing, are usually uneconomical and space-wasting. Electric-field-enhanced oil-water separation equipment was developed in this paper, and a mine field test was carried out. With the average water cut of different sampling ports and the overall dehydration rate taken as indicators, the effects of electric field frequency, inlet flow, chemical type, and addition upon the separation of the device were evaluated. The experimental results showed that for the ABJ mixed liquid, the optimal operating frequency of the electric field is above 3500 Hz. Compared with traditional separation equipment, the advantages of the electric-field-enhanced oil–water separation equipment are more significant in large flow conditions. When the water cut of the platform inlet fluctuates between 78% and 97%, and without the addition of chemicals, the average water cut was reduced to 7% and the average dehydration rate reached 90%, an improvement of about 15%.

Polymer flooding is one of the most important enhancing oil recovery (EOR) technologies in the world. With the optimization of polymer synthesis, the performance of polymer solutions has been greatly improved, which can adapt to more complex oil and gas reservoirs. However, with the continuous improvement of the properties of polymer solutions, the elastic property of polymer solutions is significantly improved, and the rheological law has also changed. This series of changes affects the application of polymer flooding reservoir numerical simulation technology. Therefore, constructing an accurate description model and precise limitation conditions is particularly important. The rheological curve with a wide shear range (0.1~10,000 s⁻¹) and the viscoelasticity of the two polymers (partially hydrolysed polyacrylamide (HPAM) and dendritic hydrophobic association polymer (DHAP)) were analyzed and tested by a rotating rheometer. The results showed that under the experimental conditions, the rheological curve of both polymers can be described by the Carreau rheological model. Meanwhile, the structural viscosity of the hydrophobically associating polymer solution (DHAP) greatly improved the elasticity of the solution and led to the change of elastic modulus. Considering the influence of elastic characteristics on the rheological curve, the relaxation time spectrum derived from small vibration experimental data was used to limit the characteristic relaxation time, that is, the value range of λ. It was observed that the experimental data were highly matched with the nonlinear regression fitting curve of the Carreau rheological model. Therefore, the relationship between different test parameters should be fully considered while studying the rheological constitutive equation of viscoelastic fluid, so as to optimize and improve the equation of it.

Polymer flooding has been gradually applied in Chinese offshore oilfields to enhance oil recovery (EOR). Injectivity loss during polymer flooding is a common issue that could cause lower displacement speed and efficiency, and eventually compromise the polymer flooding result. This paper presents a case study of a Chinese offshore field where injectivity loss issues were encountered in the polymer flooding project. A series of measures are applied to enhance the injectivity. The injectivity enhancement strategies are proposed and conducted from three main aspects, namely, (1) surface polymer fluid preparation; (2) downhole wellbore stimulation; and (3) reservoir–polymer compatibility, respectively. For the surface polymer fluid preparation, a series of sieve flow tests are conducted to obtain the optimal mesh size to improve the polymer fluid preparation quality and reduce the amount of “fish eyes”. The downhole wellbore stimulations involve oxidization-associated acidizing treatment and re-perforation. Polymer–reservoir compatibility tests are conducted to optimize the molecular weight (MW). Regarding the surface measures, the optimal filtration sieve mesh number is 200, which could reduce fish eyes to a desirable level without causing mesh plugging. After mesh refinement, the average injection pressure of the twelve injection wells decreases by 0.5 MPa. For the downhole stimulations, acidizing treatment are applied to six injection wells, which decreases the injection pressures by 6 to 7 MPa. For Well A, where acidizing does not work, the re-perforation measure is used and enhances the injectivity by 300%. Moreover, the laboratory and field polymer–reservoir compatibility tests show that the optimal polymer molecular weight (MW) is sixteen million. Proposed strategies applied from the surface, downhole, and reservoir aspects could be used to resolve different levels of injectivity loss, which could provide guidance for future offshore polymer projects.