Yung-Chuan Chiou

Prof. Yung-Chuan Chiou

orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2019 in Materials & Design
Verified
Journal Article
Open access
YCYung-Chuan Chiou
Yung-Chuan Chiou
HCHsin-Yin Chou
Hsin-Yin Chou
MSMing-Yuan Shen
Ming-Yuan Shen

1 April 2006 in Journal of the Chinese Institute of Engineers
Verified
Journal Article
Closed access
YCYung-Chuan Chiou
Yung-Chuan Chiou
MYMing‐Chuen Yip
Ming‐Chuen Yip
This study extends the plastic strain energy approach to predict the fatigue life of AISI 304 stainless steel. A modified energy parameter based on the stable plastic strain energy density under tension conditions is proposed to account for the mean strain and stress effects in a low cycle fatigue regime. The fatigue life curve based on the proposed energy parameter can be obtained directly by modifying the parameters in the fatigue life curve based on the stable plastic strain energy pertaining to fully reversed cyclic loading. Hence, the proposed damage parameter provides a convenient means of evaluating fatigue life on the mean strain or stress effect. The modified energy parameter can also be used to explain the combined effect of alternating and mean strain/stress on the fatigue life. In this study, the mean strain effects on the fatigue life of AISI 304 stainless steel are examined by performing fatigue tests at different mean strain levels. The experimental results indicate that the combination of an alternating strain and a mean strain strongly influences the fatigue life. Meanwhile, it is found that the change in fatigue life is sensitive to changes in the proposed damage parameter under the condition of a constant strain amplitude at various mean strain levels. A good agreement is observed between the experimental fatigue life and the fatigue life predicted by the proposed damage parameter. The damage parameter proposed by Smith et al. (1970) is also employed to quantify the mean strain effect. The results indicate that this parameter also provides a reasonable estimate of the fatigue life of AISI 304 stainless steel. However, a simple statistical analysis confirms that the proposed damage parameter provides a better prediction of the fatigue life of AISI 304 stainless steel than the SWT parameter.

16 January 2019 in Materials
Verified
Journal Article
Open access
PDF file
CWChia-Chin Wu
Chia-Chin Wu
YCYung-Chuan Chiou
Yung-Chuan Chiou
The study was devoted to the observation and modeling the mechanical behaviors of a hybrid SBR/NR (Styrene-Butadiene/Natural Rubber) hybrid vulcanized rubber fender under monotonic/cyclic compression. In experimental observations of the monotonic compression tests, it was found that lateral deformation occurred on the tested fender and was more significant with increasing the extent of the compressive strain. The relationship between the transmission stress S c and the compressive strain e c was nonlinear and the absorbed strain-energy-density was increased monotonically with the increment of the compressive strain. Among all cyclic compression tests with strain controlled, the reductions in both the stress range and the absorbed strain-energy-density up to the ten-thousandth cycle were found and then both of the cyclic properties remain approximately constant in the following compression cycles. Two new properties, the softening factor and the energy reduction factor, were introduced to quantify the effect of the strain range on the extent of the reduction in stress range and that on the absorbed strain-energy-density, respectively. It was found that both of the calculated values of the new properties increase with the increment of strain range. In mathematical modeling of the relationship between the transmission stress and the compressive strain, a new approach based on energy-polynomial-function E s ( e c ) was presented and was successfully used to simulate the monotonic curve and the stable hysteresis loop curves of the tested rubber fender in compression. Essentially, the energy-polynomial-function E s ( e c ) was obtained by performing a polynomial regression on a large amount of ( e c , E s ) data. Moreover, the least-square approach was applied to determine the corresponding regression coefficients in E s ( e c ) . Clearly, the stress-polynomial-function in modeling the S c − e c curve could be obtained from the differentiation of the energy-polynomial-function with respect to the compressive strain. In addition, to provide an adequate estimation of the mechanical properties of the cylindrical rubber fender under compression, the named cyclic stress-strain curve and cyclic energy-strain curve were developed and also modeled in this study.

5 March 2020 in Materials
Verified
Journal Article
Open access
PDF file
MSMing-Yuan Shen
Ming-Yuan Shen
YCYung-Chuan Chiou
Yung-Chuan Chiou
CTChung-Ming Tan
Chung-Ming Tan
CWChia-Chin Wu
Chia-Chin Wu
WCWei-Jen Chen
Wei-Jen Chen
In this study, the effect of wall thickness (15–25 mm) on the stress–strain response of hollow-cylinder rubber fenders were investigated by conducting monotonic compression tests. It was found that a progressive increase in lateral bending deformation was observed during monotonic compression. Simultaneously, the extent of the lateral deflection decreased notably with an increasing wall thickness. From the experimental results, the fact is accepted that buckling occurred in the tested fender due to the fact that the ratio of the height to the wall thickness was higher than four in all of the considered cases. Moreover, an s-shape profile appeared in the stress–strain curves, which became clearer as the wall thickness was reduced from 25 to 15 mm. To assess the performance of fenders objectively, an energy-effectiveness index, C E R , was introduced to quantify the energy absorption capacity of the fender. From the experimental observations, it was inferred that the contact area of the folded inner surface of the fender produced under compression generated an additional reaction force and affected the shape of the stress–strain curve since the measured load consisted of two reaction forces: one caused by the self-contact area, and the other resulted from the compression-bending deformation that occurred in the side wall of the fender. To examine this assertion, a finite element analysis (FEA) was conducted and confirmed the effect of the reaction force on the sensitivity of the s-shape characteristic of the stress–strain curve. Finally, a polynomial regression was conducted and the calculated results based on the fourth-degree stress polynomial function correlated very well with the measured stress–strain curves.

1 June 2015 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
LCLiang-Hsiung Chou
Liang-Hsiung Chou
YCYung-Chuan Chiou
Yung-Chuan Chiou
YHYing-Jen Huang
Ying-Jen Huang

1 March 2019 in Engineering Analysis with Boundary Elements
Verified
Journal Article
Closed access
YCYung-Chuan Chiou
Yung-Chuan Chiou
Nan-Jing WuNan-Jing Wu
Nan-Jing Wu