Covariate modeling is an important opportunity for pharmacometrics to influence decision making in drug development. The stepwise covariate model (SCM) building procedure is the most common method for covariate model development. Despite its advantages, the traditional SCM method is known to have long runtimes and the suboptimal ability to select relevant covariates, especially in more complex phase III settings. In this work, two alternative approaches are presented: SCM+, which introduces the “adaptive scope reduction” and changes to general estimation settings, and “stage‐wise filtering,” which groups covariates into categories based on their importance (mechanistic, structural, and exploratory). The three methods (SCM, SCM+, and SCM+ with stage‐wise filtering) are applied to data from a simulated phase III population pharmacokinetic study and are compared in terms of efficiency and relevance. The two SCM+ methods were considerably more efficient than the traditional SCM: the number of function evaluations was reduced by 70% for SCM+ and by 76% for SCM+ with stage‐wise filtering compared to SCM; the corresponding number of executed models was reduced by 44% for SCM+ and 70% for SCM+ with stage‐wise filtering. In addition, among the three methods, SCM+ with stage‐wise filtering selected the highest number of relevant covariates. Given the improved efficiency and ability to select relevant covariates shown in this work, the use of SCM+ and stage‐wise filtering can greatly increase the efficiency of covariate modeling in drug development, which will ultimately facilitate more timely support for decision making.
7 February 2015 in BMC Medical Informatics and Decision Making
Warfarin is the most widely prescribed anticoagulant for the prevention and treatment of thromboembolic events. Although highly effective, the use of warfarin is limited by a narrow therapeutic range combined with a more than ten-fold difference in the dose required for adequate anticoagulation in adults. An optimal dose that leads to a favourable balance between the wanted antithrombotic effect and the risk of bleeding as measured by the prothrombin time International Normalised Ratio (INR) must be found for each patient. A model describing the time-course of the INR response can be used to aid dose selection before starting therapy (a priori dose prediction) and after therapy has been initiated (a posteriori dose revision). In this paper we describe a warfarin decision support tool. It was transferred from a population PKPD-model for warfarin developed in NONMEM to a platform independent tool written in Java. The tool proved capable of solving a system of differential equations that represent the pharmacokinetics and pharmacodynamics of warfarin with a performance comparable to NONMEM. To estimate an a priori dose the user enters information on body weight, age, baseline and target INR, and optionally CYP2C9 and VKORC1 genotype. By adding information about previous doses and INR observations, the tool will suggest a new dose a posteriori through Bayesian forecasting. Results are displayed as the predicted dose per day and per week, and graphically as the predicted INR curve. The tool can also be used to predict INR following any given dose regimen, e.g. a fixed or an individualized loading-dose regimen. We believe that this type of mechanism-based decision support tool could be useful for initiating and maintaining warfarin therapy in the clinic. It will ensure more consistent dose adjustment practices between prescribers, and provide efficient and truly individualized warfarin dosing in both children and adults.
4 January 2022 in CPT: Pharmacometrics & Systems Pharmacology
The full random‐effects model (FREM) is a method for determining covariate effects in mixed‐effects models. Covariates are modeled as random variables, described by mean and variance. The method captures the covariate effects in estimated covariances between individual parameters and covariates. This approach is robust against issues that may cause reduced performance in methods based on estimating fixed effects (e.g., correlated covariates where the effects cannot be simultaneously identified in fixed‐effects methods). FREM covariate parameterization and transformation of covariate data records can be used to alter the covariate‐parameter relation. Four relations (linear, log‐linear, exponential, and power) were implemented and shown to provide estimates equivalent to their fixed‐effects counterparts. Comparisons between FREM and mathematically equivalent full fixed‐effects models (FFEMs) were performed in original and simulated data, in the presence and absence of non‐normally distributed and highly correlated covariates. These comparisons show that both FREM and FFEM perform well in the examined cases, with a slightly better estimation accuracy of parameter interindividual variability (IIV) in FREM. In addition, FREM offers the unique advantage of letting a single estimation simultaneously provide covariate effect coefficient estimates and IIV estimates for any subset of the examined covariates, including the effect of each covariate in isolation. Such subsets can be used to apply the model across data sources with different sets of available covariates, or to communicate covariate effects in a way that is not conditional on other covariates.
17 April 2022 in CPT: Pharmacometrics & Systems Pharmacology
Understanding the uncertainty in parameter estimates or in derived secondary variables is important in all data analysis activities. In pharmacometrics, this is often done based on the standard errors from the variance–covariance matrix of the estimates. Confidence intervals derived in this way are by definition symmetrical, which may lead to implausible outcomes, and will require translation to generate uncertainties in derived variables. An often‐used alternative is numerical percentile estimation by, for example, nonparametric bootstraps to circumvent these issues. Visual predictive checks (VPCs), which is a commonly used model diagnostic tool in pharmacometric analyses, also rely on the estimation of percentiles through numerical approaches. Given the cost in terms of run times and processing times for these methods, it is important to consider the trade‐off between the number of bootstrap samples or simulated data sets in the VPCs, to the increase in precision related to a large number of bootstrap samples or simulated data sets. The objective with this tutorial is to provide a quantitative framework for assessing the precision in estimated percentile limits in bootstrap and visual predictive checks analyses to facilitate an informed choice of confidence interval width, number of bootstrap samples/simulated data sets, and required level of precision.
28 February 2024 in CPT: Pharmacometrics & Systems Pharmacology
The inclusion of covariates in pharmacometric models is important due to their ability to explain variability in drug exposure and response. Clear communication of the impact of covariates is needed to support informed decision making in clinical practice and in drug development. However, effectively conveying these effects to key stakeholders and decision makers can be challenging. Forest plots have been proposed to meet these communication needs. However, forest plots for the illustration of covariate effects in pharmacometrics are complex combinations of model predictions, uncertainty estimates, tabulated results, and reference lines and intervals. The purpose of this tutorial is to outline the aspects that influence the interpretation of forest plots, recommend best practices, and offer specific guidance for a clear and transparent communication of covariate effects.
1 December 2004 in Journal of Pharmacokinetics and Pharmacodynamics