Fracture or chipping are major concerning failures of an all-ceramic restoration. Repairing of the failure restoration using intra-oral technique is time saving and cost effective treatment modality. The present study was proposed to evaluate effect of Er,Cr:YSGG laser irradiation on shear bond strength between zirconia/porcelain and composite resin. Thirty zirconia and thirty zirconia based porcelain disc shape specimens were prepared. Three different surface treatment procedure were applied the specimens. For control groups (Group ZC and PC), instruction manual of an intra-oral porcelain repair system was followed. Different pulse rates of Er,Cr:YSGG laser irradiation (short and long pulses) were applied to zirconia and porcelain surfaces for other groups (Group ZS, ZL, PS, and PL). Porcelain repair kit was used to repair specimens using standard cylindrical teflon mold (2 × 2 mm). Repair bond strength of the repaired specimens was tested using a universal testing machine. Highest mean bond strength value was observed at Group PC that was significantly higher than laser applied porcelain groups. Long pulse laser irradiation illustrated that increased mean bond strength compared to short pulse application on to the porcelain surface. Laser applied zirconia groups showed better mean bond strength than Group ZC, but differences between the groups were not statistically significant. Different modes of Er,Cr:YSGG laser irradiation enhanced repair bond strength of the composite resin to zirconia, but these were not significant. Following the instruction manual for surface treatment on the porcelain surface was better method than Er,Cr:YSGG laser surface conditioning.

The various advantages of crown materials produced using three-dimensional (3D) printers have increased their use in restorative and prosthetic dentistry in recent years. Accordingly, their optical and mechanical properties have become more important. To evaluate the mechanical, surface and optical properties of crown materials produced with 3D printing and computer-aided design (CAD)/computer-aided manufacturing (CAM), which has recently been used frequently in the clinic. The 3-point bending test was used to evaluate the mechanical properties of 2 different crown materials produced with 3D printing (Permanent Crown and VarseoSmile Crown Plus) and a crown material produced using CAD/CAM (Vita Enamic). After the initial color and surface roughness measurements were made, the specimens were immersed in 4 different solutions. The most translucent material was VarseoSmile Crown Plus (p < 0.05). In all specimens, coffee caused the most discoloration (p < 0.05). The effects of the solutions on the roughness were mostly observed in Permanent Crown specimens (p < 0.05). Vita Enamic showed the highest statistically significant values in terms of flexural strength (p < 0.05). The stereolithographic technique among the materials produced by 3D printing can be recommended for use in restorations due to its higher flexural strength.

The aim of this study was to investigate the effects of different surface treatment methods on shear bond strength between composite resin and different levels of zirconia ceramic. Laser surface-conditioning procedures have been reported as effective method to increase repair bond strength of composite to zirconia ceramics. Detailed information of effects of Er,Cr:YSGG laser treatment with different pulse rates on the zirconia ceramics is lacking in the literature. 120 disc-shaped specimens were prepared including zirconia, veneering ceramic, and 50 veneering ceramic-50 zirconia surfaces. Four different surface treatments were applied to the specimens. These were grinding with diamond bur, sandblasting, and short and long pulse rates of Er,Cr:YSGG laser irradiation. An intraoral ceramic repair kit was used to repair specimens, and shear bond strength was performed on the composite resin to each specimen. The highest mean bond strength was seen in the veneering ceramic surface that was ground using a diamond bur, and the lowest mean bond strength value was observed in the same surface that was treated with long pulse laser irradiation. The sandblasting with alumina particles exhibited lower mean repairing bond strength among the rest of used methods in this study for the group which contained half of the veneering ceramic and half of the zirconia. Sandblasting and Er,Cr:YSGG laser using surface treatment procedures obtained appropriate bond strength for the group that included 50 veneering ceramic-50 zirconia, because of no significant differences observed among the applied surface conditioning methods in this group.

Emre Tokar, DDS, PhD/Bulent Uludag, DDS, PhD: Purpose: Many different attachment systems (eg, bars, studs, magnets, telescopic copings) have been used to retain overdentures. The current study aimed to investigate the load transfer characteristics and to compare the stress levels of four attachment designs for mandibular overdentures retained by one central implant and two inclined distal implants. Materials and Methods: Photoelastic mandibular models fabricated with three screw-type implants (Tapered Screw-Vent, 3.75 ? 13 mm) were placed in the parasymphyseal area. The center implant was vertically oriented to the midline, and the other implants were embedded in the canine areas with a 20-degree angulation relative to the center implant. Four overdentures with different attachment designs (bar, bar/ball, bar/distally placed Rk-1s, and Locators) were studied in the context of this model. Vertical loads (100 N) were applied to the central fossa of the right first molar area of each overdenture. Stress levels that developed in the denture-bearing areas and around the implants were observed photoelastically and evaluated visually. Results: The studied attachment designs showed low and moderate stress levels. The greatest stress was found with the bar/ball design, while the lowest stress levels were observed with the Locator attachment design. Conclusion: Stresses were concentrated on the loaded side for each design. All tested designs experienced moderate stress around the posterior edentulous area. None of the designs experienced more than moderate stress. The lowest stress was noted with the Locator attachments, which transmitted little discernible stress around the implants.