Nilam Barekar

Dr. Nilam Barekar

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2012 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
SSSunitha Jallepalli Satya
Sunitha Jallepalli Satya
VKVivek Kumar
Vivek Kumar
NBNilam Barekar
Nilam Barekar
KBKoushik Biswas
Koushik Biswas
BDBrij Dhindaw
Brij Dhindaw

27 April 2011 in Journal of Materials Research
Verified
Journal Article
Closed access
PDF file
NBNilam Barekar
Nilam Barekar
PGPiter Gargarella
Piter Gargarella
Kaikai SongKaikai Song
Kaikai Song
SPSimon Pauly
Simon Pauly
UKUta Kühn
Uta Kühn
JEJürgen Eckert
Jürgen Eckert

23 November 2013 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
NBNilam Barekar
Nilam Barekar
RPR. Pradhan
R. Pradhan
BDB. K. Dhindaw
B. K. Dhindaw

22 February 2025 in Materials Letters
Verified
Journal Article
Open access
PSPavel Shurkin
Pavel Shurkin
GSG. Scamans
G. Scamans
TST. Subroto
T. Subroto
NBNilam Barekar
Nilam Barekar
FSFazlollah Sadeghi
Fazlollah Sadeghi
CBC. Barbatti
C. Barbatti

25 January 2022 in JOM
Verified
Journal Article
Open access
PDF file
NBNilam Barekar
Nilam Barekar
ISIvan Skalicky
Ivan Skalicky
SWShihao Wang
Shihao Wang
PSPavel Shurkin
Pavel Shurkin
OAOnuh Adole
Onuh Adole
MJMartin Jarrett
Martin Jarrett
Al-Si wrought piston alloys can lack properties due to inefficient grain refining. A novel Al-Nb-B grain refiner was introduced some time ago, but has still not been assessed in industry for wrought alloys. This paper describes the first trial of Al-Ni-B addition and its impact on the full-scale manufacturing, structure, and properties of the AA4032 products extruded with and without billet homogenization. It is shown that Nb-B inoculation gives opportunities not only to have a refined as-cast structure but also a more homogenous distribution of the solute. In contrast, homogenization drives nucleation and coarsening of the Mg2Si phase that is retained during further extrusion and heat treatment also affecting the precipitation and properties. It was observed that non-homogenized specimens perform better during machining and tensile testing compared to homogenized specimens. The results are supported by electron microscopy investigations of microstructure formation during different steps in downstream processing.

Verified
Journal Article
Open access
PDF file
AAAbdul Radim Asil
Abdul Radim Asil
NBNilam Barekar
Nilam Barekar
CBCarla Barbatti
Carla Barbatti
DEDmitry Eskin
Dmitry Eskin
Demand for aluminium (Al) products has increased due to their low density, high strength-to-weight ratio, thermal and electrical conductivity, and corrosion resistance. Reliable machinability assessment is important for selecting suitable alloys for manufacturing applications. However, conventional methods based on chip counting and weighing may not adequately distinguish alloys with similar chemical compositions. This study proposes an alternative method for assessing aluminium alloy machinability by quantifying the Shear Crack Initiation Layer (SCIL) in machining chips. Aluminium alloys were machined using a lathe under consistent machining parameters, and chip cross-sections were examined to quantify shear crack features and investigate differences between inner and outer chip layers. Conventional chip counting and weighing produced similar machinability values for two chemically similar alloys and showed negligible differences between the inner and outer layers of each alloy. In contrast, SCIL-based assessment revealed clear machinability differences between the inner and outer layers within each alloy and between the two chemically similar alloys. These findings demonstrate the potential of SCIL quantification to provide a more sensitive assessment of aluminium alloy machinability than conventional chip counting and weighing methods.