Velocity model inversion is one of the most challenging tasks in seismic exploration, and an accurate velocity model is essential for high-resolution seismic imaging. Recently, velocity inversion methods based on deep learning (DL), particularly convolutional neural networks (CNNs), have attracted considerable attention from the seismic exploration community. These researchers aim to directly estimate the velocity model from raw seismograms using a well-trained model. Although CNN-based velocity inversion methods have demonstrated remarkable performance in terms of intelligence and automation, their inversion performance is often constrained by a limited long-range dependence. Specifically, when conducting a convolutional operation on raw seismic data using small kernels (i.e., 1 × 1, 3 × 3, 5 × 5, and 7 × 7), CNN-based methods extract only the local features and neglect the weak spatial correlation between different local features that reflect the information of the same interface. This correlation could assist CNN in providing an overview of the seismic data and promote inversion performance when using DL. Furthermore, the time-varying properties of seismic data pose a challenge to the weight sharing of CNNs. Here, we have developed a new DL framework based on a transformer, called the seismic velocity inversion transformer (SVIT), to address the problem of velocity inversion. SVIT uses a self-attention mechanism to capture the long-range dependence of seismic data, rather than stacking multiple convolutional layers as in CNNs. Thus, SVIT can provide more informative remote features for building velocity models. The validity and reliability of the proposed method are demonstrated through numerical experiments using synthetic models. Compared with the conventional full-waveform inversion method and an existing CNN-based velocity inversion method, our SVIT indicates greater consistency with the target in terms of the velocity value, subsurface structures, and geologic interfaces and is expected to provide a new DL-based solution to resolve inversion problems.
For surveys in areas with difficult access, ground-based electromagnetic (EM) systems are difficult to operate, time-consuming, and expensive, whereas airborne EM (AEM) systems are unsafe and uneconomic for small survey areas. We have developed a new frequency-domain airborne electromagnetic (FAEM) system called the ground-airborne frequency-domain EM (GAFEM) system to achieve rapid data acquisition in complex terrains with high safety and low cost. The system consists of a grounded electrical source and an airborne receiver carried by an unmanned rotorcraft. The grounded electrical source transmits a [ ] pseudorandom series obtaining signals at [ ] frequencies in one flight, which can maintain the resolution without reducing efficiency. The airborne receiver based on the unmanned rotorcraft makes the system flexible, convenient, and economical to operate in areas with difficult access. The system can conduct surveys in far- and non-far-field regions and can obtain the apparent resistivity to present a quick overview of the subsurface structure. To demonstrate the GAFEM system’s effectiveness and practical detection potential, we have performed two field surveys that revealed the shallow structure with tunnels and the deep structure at source-receiver distances of 3 and 6 km, respectively. The GAFEM system effectively revealed the apparent-resistivity difference with a sufficient investigation depth at large source-receiver distances. Thus, the system can be extended to various important applications for rapid surveys or deep investigations in areas with difficult access.
26 May 2022 in IEEE Transactions on Geoscience and Remote Sensing
Seismic background noise often damages the desired signals, thereby resulting in some artifacts in the seismic imaging that follows. Since about 2016, some supervised-deep-learning methods have shown impressive performance in seismic data denoising, but they usually only consider single-scale features and neglect the multi-scale strategy. To further reinforce their denoising performance, a novel multi-scale convolutional neural network (CNN) combined with spatial attention mechanism, called multi-scale spatial attention denoising network (MSSA-Net), is proposed to tell weak reflected signals apart from strong seismic background noise. Unlike conventional single-scale CNNs, this proposed MSSA-Net can achieve the extraction of multi-scale features which is beneficial for the suppression of strong noise and the recovery of weak reflected signals. Specifically, MSSA-Net contains a principal denoising network and two auxiliary networks. The former utilizes the widen convolution composed of multiple parallel convolution layers with different kernel sizes to capture the informative multi-scale features; the latter two leverage up and down sampling to extract local fine and global coarse features, respectively. Furthermore, a spatial attention block is adopted to fuse these multi-scale features, thereby distinguishing weak reflected signals from strong seismic background noise. Multiple experiments of synthetic and real seismic records demonstrate the effectiveness of MSSA-Net. In addition, compared with two classical single-scale CNNs, MSSA-Net performs better in signal recovery, indicating the positive effect of multi-scale strategy.
5 December 2019 in IEEE Geoscience and Remote Sensing Letters
Road collapse and underground water inrush accidents pose a serious threat to urban safety and development. Transient electromagnetic (TEM) method is an effective geophysical method for detecting urban underground space. However, due to the complexity of urban geological environment, the conventional TEM detection methods are difficult to meet the needs of efficient and high-resolution detection of urban underground space. To solve this problem, an adaptive high-resolution (AHR) TEM detection method based on pseudoseismic wavelet transform technology is proposed in this study. The simulation results show that compared with the conventional technologies, the AHR detection method can more accurately reflect the resistivity distribution information in complex geological environment. The proposed method is implemented to detect an urban underground cavity, and the imaging results are consistent with the actual results. The research results will provide technical support for the early warning of road collapse and water inrush in urban industrial development.