Ossi Martikka

Dr. Ossi Martikka

LAB University of Applied Sciences
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 April 2010 in Applied Composite Materials
Verified
Journal Article
Closed access
PDF file
SBSvetlana Butylina
Svetlana Butylina
Ossi MartikkaOssi Martikka
Ossi Martikka
TKTimo Kärki
Timo Kärki

1 October 2015 in Polymer Degradation and Stability
Verified
Journal Article
Closed access
SBSvetlana Butylina
Svetlana Butylina
Ossi MartikkaOssi Martikka
Ossi Martikka
TKTimo Kärki
Timo Kärki

12 July 2011 in Polymer-Plastics Technology and Engineering
Verified
Journal Article
Closed access
SBSvetlana Butylina
Svetlana Butylina
Ossi MartikkaOssi Martikka
Ossi Martikka
TKTimo Kärki
Timo Kärki
The physical and mechanical properties of wood-polymer composites made with virgin or recycled polypropylene, or a mixture of these were studied. The composites made with recycled polypropylene had higher density, lower porosity, and higher dimensional stability compared to the composites made with virgin polypropylene. Although the composites made with recycled polypropylene exhibited lower tensile strength than those made with virgin polypropylene, they had higher Charpy impact strength. Scanning electron microscopy analysis of the fractured surfaces of the composites showed no significant differences in the fracture mechanisms of the studied composites. The degree of crystallinity was estimated to be higher for the virgin polypropylene than for the recycled one.

1 March 2010 in Wood Material Science & Engineering
Verified
Journal Article
Closed access
THTiina Huuhilo
Tiina Huuhilo
Ossi MartikkaOssi Martikka
Ossi Martikka
SBSvetlana Butylina
Svetlana Butylina
TKTimo Kärki
Timo Kärki

31 August 2018 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
Ossi MartikkaOssi Martikka
Ossi Martikka
TKTimo Kärki
Timo Kärki
QWQing Ling Wu
Qing Ling Wu
3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

1 September 2010 in Wood Material Science & Engineering
Verified
Journal Article
Closed access
SBSvetlana Butylina
Svetlana Butylina
Ossi MartikkaOssi Martikka
Ossi Martikka
TKTimo Kärki
Timo Kärki
This study focuses on the water absorption and mechanical properties of composites made from softwood sawdust and plastics, such as virgin and recycled polypropylene and polylactic acid (PLA). The composites were processed by extrusion, and their properties were investigated by a water immersion test, mechanical tests and a cyclic test for moisture resistance. Scanning electron microscopy was used to study the morphology of the fracture surfaces of the composites. The composites made with recycled polypropylene had the lowest water absorption and thickness swelling of the studied composites. The PLA composites made with heat-treated sawdust showed the highest flexural strength. Of the polypropylene based composites, virgin polypropylene resulted in composites with higher flexural strength. The Charpy impact strength of the composites was found to have an inverse trend compared to flexural strength. Cyclic treatment of the studied composites resulted in 20–60% loss of flexural strength, depending on type of composite.