Yurii Halynkin Yurii

Dr. Yurii Halynkin Yurii


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 January 2025 in Proceedings of the Bulgarian Academy of Sciences
Verified
Journal Article
Open access
PDF file
WHWeidong Hui
Weidong Hui
Serhii ShevchenkoSerhii Shevchenko
Serhii Shevchenko
MKMykola Korchak
Mykola Korchak
ALAndrei Lesko
Andrei Lesko
AMAndrii Monakhov
Andrii Monakhov
OGOleksandr Gerasin
Oleksandr Gerasin
The operating experience of mechanical seals shows that as a result of angular deformations of the rings, wear of the contact surfaces along radius is uneven. In the area of hydrodynamic load support in the case of a confusor joint or a converging film, the slope of the pressure diagram is such that a decrease in the film thickness increases the hydrodynamic support. This enables stable non-contact sealing operation. When designing mechanical seals, it is necessary to calculate the deformations of the sealing rings caused by both the pressure of the medium being sealed and thermal effects in order to predict the size and direction of the radial cone and avoid unstable operation of the seal. The execution of the rubbing surfaces of the interface of the end pair should ensure the formation of the calculated confusor shape of the sealing gap in all modes of operation.

19 January 2021
Verified
Book Chapter
Closed access
PDF file
МТМихаил Ткач
Михаил Ткач
YZYurii Zolotoy
Yurii Zolotoy
YYYurii Halynkin Yurii
Yurii Halynkin Yurii
APArkadii Proskurin
Arkadii Proskurin
IZIrina Zhuk
Irina Zhuk
IBIgor Bobylev
Igor Bobylev

1 March 2021 in Acta Mechanica et Automatica
Verified
Journal Article
Open access
PDF file
MTMykhaylo Tkach
Mykhaylo Tkach
YYYurii Halynkin Yurii
Yurii Halynkin Yurii
APArkadii Proskurin
Arkadii Proskurin
IZIrina Zhuk
Irina Zhuk
VKVolodymyr Kluchnyk
Volodymyr Kluchnyk
IBIgor Bobylev
Igor Bobylev
The compact installation and technology for determining vibration characteristics by the ESPI method has been created. The experimental determination of the dynamic characteristics of a diamond circular blade with a diameter of 203.4 mm and a thickness of 1.19 mm using real-time electronic speckle interferometry is presented. 15 mode shapes of vibration were detected in the range from 100 to 5000 Hz. The program calculation of the natural frequencies and mode shapes is carried out for three values of the clamping inner diameter (42 mm, 44 mm, 46 mm). The options for calculating a disk with a rim and without a rim are considered. It is shown that the minimum mean squared error of the calculation is achieved for the values of the diameter of the disk 46 mm, 42 mm and 44 mm for the number of nodal circles 0, 1 and 2, respectively. To verify the accuracy of the interferometer, experimental, computational and analytical studies of console steel rod 200 × 22.25 × 3.78 mm in size were carried out.

1 January 2025 in Collection of Scientific Publications NUS
Verified
Journal Article
Closed access
OSOleksandr P. Shumilov
Oleksandr P. Shumilov
YYYurii Halynkin Yurii
Yurii Halynkin Yurii
VSViktor M. Sichko
Viktor M. Sichko
OKOleksandr A. Kostrikov
Oleksandr A. Kostrikov

31 August 2019 in Aerospace technic and technology
Verified
Journal Article
Open access
PDF file
МТМихаил Ткач
Михаил Ткач
БТБорис Георгійович Тимошевський
Борис Георгійович Тимошевський
АПАркадій Юрійович Проскурін
Аркадій Юрійович Проскурін
YYYurii Halynkin Yurii
Yurii Halynkin Yurii
The article discusses a promising energy-technology unit for the extraction of hydrogen sulfide from the deep waters of the Black Sea, which provides for raising the gas-liquid mixture from the depths by the gas-lift method using wave pulses to separate hydrogen sulfide in the gaseous state. The installation includes a supply line, which is lowered to the required depth, a supply pump, a coalescing separator, a seawater discharge line with a reduced concentration of hydrogen sulfide, a control valve, a hydrodynamic generator of mechanical vibrations, a lifting pipeline, a high pressure hydrogen sulfide separator, a hydraulic turbine, a low pressure hydrogen sulfide separator, seawater discharge pipe and hydrogen sulfide expander. This unit will improve the energy efficiency and operational reliability of the process of hydrogen sulfide production, as well as reduce the burden on the Black Sea environment. A mathematical model of this setup has been developed. The results obtained by the mathematical model adequately coincide with the known experimental ones. This suggests that it is possible to use the model to determine the parameters of the process for the extraction of hydrogen sulfide from the Black Sea. The parameters of the process for the extraction of hydrogen sulfide from the Black Sea in the depth range of the pipeline 0...1000 m at a temperature of 280...285 K. It has been established that increasing the gas content of seawater from 0 to 2.5 m3/m3 leads to a decrease in the pressure value by 2.2 MPa. A further increase in seawater gas content from 2.5 to 5.0 m3/m3 is accompanied by a decrease in pressure of another 1.6 MPa. Such a significant decrease in pressure at the inlet to the riser piping allows hydrogen sulfide and seawater to be obtained at a pressure that is substantially greater than atmospheric. The excess pressure at the outlet of the lifting pipeline is determined based on data obtained by the method of "equivalent length". When the seawater gas content is 2.5 m3/m3, the pipeline’s immersion depth is 250...1000 m, the value of the overpressure of substances at the exit of the lifting pipeline will be 0.2...0.45 MPa, and at 5 m3/m3 – 0.67...1.07 MPa, at 7.5 m3/m3 – 0.83...1.4 MPa and at 10 m3/m3 – 0.97...1.68 MPa.

22 August 2022 in Aerospace technic and technology
Verified
Journal Article
Closed access
PDF file
МТМихаил Ткач
Михаил Ткач
SKSergey Kulishov
Sergey Kulishov
Vitaliy PolishchukVitaliy Polishchuk
Vitaliy Polishchuk
YYYurii Halynkin Yurii
Yurii Halynkin Yurii
APArkadіі Proskurin
Arkadіі Proskurin
VKVladimir Kluchnyk
Vladimir Kluchnyk
A description of the stand based on a digital speckle interferometer with a diffuse reference wave and separated branches is given, which allows determining the natural frequencies and vibration modes of objects in real time. In the frequency range 100...4000 Hz, an experimental study of the vibration characteristics of a turbine rotor blade of a gas turbine engine was carried out, with rigid fastening of the blade fir tree part, which was achieved by fixing the blade in the lock and then fixing it in the clamping device. In the frequency range from 100 to 4000 Hz, 9 blade vibration modes were identified. The object of the study is the turbine rotor blade of a gas turbine engine with a height along the trailing edge of 288 mm and a chord in the middle section of 88.5 mm. A solid-state geometric model of a rotor blade based on a faceted body obtained from 3D scanning has been created. Concerning the frequency range 100...4000 Hz, using the ANSYS Workbench software package, a series of calculations of the resonant frequencies of the blade by the finite element method was carried out. Many vibration modes have been obtained, and the data obtained from experiments and calculations have been compared. The analysis of the spectrum of the natural vibration frequencies of the blade showed that the root-mean-square value of the deviations between the results obtained is 5.5% for the same modes. To verify the software calculation, the values of the resonance frequencies were recalculated using a three-dimensional model of the blade fixed in the lock. To determine the influence of the boundary conditions for fixing a gas turbine blade on its vibration characteristics, a series of calculations of the resonance frequencies and vibration modes of the blade model with cutting off a part of the blade at different heights was carried out. It is shown that cutting off the fir tree part of the blade root when modeling the boundary conditions of fixing makes it possible to simplify the calculation process by simplifying the geometry of the three-dimensional model of the blade under study, with a minimum loss of calculation accuracy.