Olivier PLE

Prof. Olivier PLE

Head of The French Academic Association of Civil Engineering, LOCIE Laboratory, Université Savoie Mont Blanc, UMR CNRS 5271, 73000 Chambéry, France
orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
PCParul Chauhan
Parul Chauhan
NPNoémie Prime
Noémie Prime
Olivier PLEOlivier PLE
Olivier PLE
Rammed earth has the potential to reduce the carbon footprint and limit the energy consumption in the building sector due to its sustainable characteristics. Still, its use is not generalized due to a lack of understanding of the material behavior, notably its sensitivity to water. The coupled hydro-mechanical behavior has been recently studied in the framework of unsaturated soil mechanics, using suction as the parameter to represent the hydric state. This dependency of the mechanical behavior on the hydric state leads to uncertainty of the drying period required to progress in the construction process. Notably, the drying period before building the next floor is unknown. To determine the drying period, thermo-hydro-mechanical coupled finite element method simulations were carried out on a single wall by using the unsaturated soil mechanics approach and safety criterion recommendations from the practical guide for rammed earth construction in France. It was determined that it takes significant time for the construction of additional floor both in ‘summer-like’ and ‘winter-like’ environmental conditions, whereas the walls were far away from the ultimate failure state. Thus the drying periods were overestimated. It was concluded that the safety criterion from the practical guide is very conservative and drying periods can be reduced without significantly compromising the safety factor.

4 February 2018 in Sustainability
Verified
Journal Article
Open access
PDF file
TTTrần Minh Tùng
Trần Minh Tùng
Quoc-Bao BuiQuoc-Bao Bui
Quoc-Bao Bui
BSBastian Okto Bangkit Sentosa
Bastian Okto Bangkit Sentosa
NNNhat-Tien Nguyen
Nhat-Tien Nguyen
TDTrung-Hieu Duong
Trung-Hieu Duong
Olivier PLEOlivier PLE
Olivier PLE
Beam-column joints are critical regions for reinforced concrete (RC) frames subjected to earthquakes. The steel reinforcement is, in general, highly concentrated in these zones. This is why in many cases, headed bars are used. A headed bar is a longitudinal steel reinforcement whose end has a special button added to reduce the bonding length of the steel rebar. This paper establishes a formula predicting the shear strength of exterior RC beam-column connections where the beam longitudinal reinforcements use headed bars. A database was collected, which contained 30 experimental data about the exterior beam-column joints using headed bars and subjected to quasi-static cyclic loading. First, from the collected database, a statistical study was carried out to identify the most influencing parameters on the shear strength of the beam-column joints tested. The three most important parameters were identified and an empirical modified formula was developed based on the formula existing in the standards. The study showed that the results obtained from the modified formula proposed in the present study were closer to the experimental results than that obtained from the formula existing in the standards. Finally, a numerical study was performed on two T-form RC structures and the numerical results were compared with the prediction calculated from the modified formula proposed. For two investigated cases, the proposed formula provided the results in the safety side and the differences with the numerical results were less than 20%. Thus, the proposed formula can be used for a rapid assessment of the shear strength of RC joints using headed bars.

15 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
Walid DebouchaWalid Deboucha
Walid Deboucha
IAIbrahim Alachek
Ibrahim Alachek
JPJean-Patrick Plassiard
Jean-Patrick Plassiard
Olivier PLEOlivier PLE
Olivier PLE
The need for retrofitting existing masonry structures is progressively becoming more important due to their continuous deterioration or need to meet the current design requirements of Eurocodes. Textile-Reinforced Mortar (TRM) composite systems have emerged as a sustainable repair methodology suitable for structure retrofitting. Nevertheless, their mechanical performance is still far from being fully investigated. This paper presents an experimental study on the tensile and bond behaviors of a new mortar-based composite consisting of mineral additives, blended cement mortar, and stainless-steel grid. Three different mineral additives (silica fume, fly ash, and blast furnace slag), in binary and ternary systems were used. The experimental study included uniaxial tensile coupon testing on composite specimens and bond tests on composite material applied to clay-brick substrate. The results obtained with the different textile-reinforced cement-based mortars were compared and are discussed here. It was found that, for mortar formulations containing mineral additives—such as fly ash or blast-furnace slag—with high tensile and bond strengths, an adequate adherence between the constituents was obtained. The developed mortar presents mechanical performances equivalent to traditional mortars without additives. The study contributes to the existing knowledge regarding the structural behavior of TRM and promotes the development of a low impact carbon cementitious matrix.

24 November 2018 in European Journal of Environmental and Civil Engineering
Verified
Journal Article
Closed access
HAHashem Abdou
Hashem Abdou
FEFabrice Emeriault
Fabrice Emeriault
Olivier PLEOlivier PLE
Olivier PLE
The phenomenon of suffusion corresponds to the migration of eroded particles in a porous media under the action of an internal flow. This mechanism could be the main origin of damage in embankments and earth dams. Many experimental studies have been conducted to understand this phenomenon. Numerically, only few studies can be found which associate the mechanisms of detachment, transport and deposition of eroded particles. In this paper, based on the classical erosion law, a new hydro-mechanical approach at the scale of a representative elementary volume is presented. The model takes into account the notions of erosion mechanism and deposition mechanism by gravitational sedimentation. These mechanisms are separated, characterised and classified by flow velocity thresholds of each one. However, a finite element solution to the equations will predict the time-dependent change of porosity and flow rate of eroded particles through the pores. The model performed using the software ‘COMSOL multiphysics’, explicitly combines erosion, transport and deposition of eroded particles. This study discusses three aspects: the general framework of the proposed model, a numerical calibration based on a 3D modelling of a new apparatus called Cross Erosion Test (CET) and finally a simulation based on CET experimental results.

19 June 2019 in Structural Engineering International
Verified
Journal Article
Closed access
BSBastian Okto Bangkit Sentosa
Bastian Okto Bangkit Sentosa
QBQuoc-Bao Bui
Quoc-Bao Bui
Olivier PLEOlivier PLE
Olivier PLE
JPJean-Patrick Plassiard
Jean-Patrick Plassiard
PPPascal Perrotin
Pascal Perrotin
At present, dynamic measurements enable the diagnosis of an existing structure at a global scale (the whole structure), while the identification and assessment of local damage (at each element of the structure) remain to be explored. In this study, diagnosis at a local scale was experimentally investigated on a reinforced concrete (RC) frame structure consisting of two columns and one beam. The RC frame was loaded in several stages and dynamic measurements were recorded at each unloading stage using accelerometers. The experimental results were first presented: the appearance of damage, the evolution of natural frequencies and the stiffness changes. Then, a technique of damage characterization was applied which takes into account the semi-rigid connections of the frame. The stiffness of the connections was identified by calibrating the numerical dynamic responses with those obtained from the experiment. Fixity factors were introduced to assess the stiffness changes in the semi-rigid connections. The validity of the identified fixity factors was evaluated using the static experimental results. This study showed that the results from dynamic measurements coupled with a simple finite element model could provide a rapid and effective method to assess the damage evolution of RC frame structures.

1 June 2002 in Materials and Structures
Verified
Journal Article
Closed access
PDF file
Olivier PLEOlivier PLE
Olivier PLE
OBO. Bayard
O. Bayard