Minyu Ma

Dr. Minyu Ma


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 July 2025 in Surface Science and Technology
Verified
Journal Article
Open access
PDF file
XWXiang Wei
Xiang Wei
YMYanlong Ma
Yanlong Ma
MMMinyu Ma
Minyu Ma
SZSheng Zhang
Sheng Zhang
MLMinghao Li
Minghao Li
Liang WuLiang Wu
Liang Wu
Plasma electrolytic oxidation (PEO) is commonly employed to enhance the corrosion resistance of magnesium and its alloys. However, the formation of pores during this process can compromise the corrosion resistance of the PEO coating. In this study, the PEO coating on an AZ91D magnesium alloy was subjected to post-treatment in Cr2(SO4)3 solutions to further improve its corrosion resistance. The structural characteristics and corrosion resistance (evaluated in a 3.5% NaCl solution) after Cr2(SO4)3 sealing treatment were investigated. The results revealed that, in the acidic sealing solution, oxides such as MgO and Mg2SiO4 in the PEO coating were dissolved, resulting in a local increase in pH. This pH increase promoted the precipitation of Cr2O3 and Cr(OH)3, which filled the micropores of the PEO coating. As the sealing time progressed, an outer layer containing Cr2O3 and Cr(OH)3 formed on the coating surface, enhancing the compactness of the PEO coating. The resistance of the PEO coating increased from 5.13 × 105 Ω cm2 to 1.56 × 106 Ω cm2 after sealing for 60 min. The average hydrogen evolution volume decreased from 21.77 ml/cm2 to 0.2 ml/cm2 (after immersion in 3.5% NaCl solution for 7 days); and no visible corrosion products were detected on the surface of the sealed samples after immersion for 100 h. These findings suggest that trivalent chromium sealing is a promising method that can effectively enhance the corrosion resistance of PEO coatings on magnesium alloys.

16 November 2024 in Metals
Verified
Journal Article
Open access
PDF file
XDXiuping Ding
Xiuping Ding
RLran Li
ran Li
PJPengfei Jin
Pengfei Jin
WWWeijie Wang
Weijie Wang
ZCzhang cheng
zhang cheng
JHJinfeng Huang
Jinfeng Huang
Cold pilgering is widely utilized in high-end applications for the precise shaping of seamless tubes due to its capacity for large deformation, which reduces the number of deformation processes and shortens production cycles. However, there is a gap in the research on the cold pilgering of small-diameter, thick-walled seamless tubes, specifically those with an outer diameter–wall thickness ratio of ≤3. In this study, cold pilgering tests were performed on Cr-Mo-V hot-working die steel small-diameter thick-walled tubes. It was discovered that increasing the feed rate results in greater deviations in both inner diameter and wall thickness, although it has little effect on inner wall roughness. In contrast, increasing wall thickness reduction leads to higher wall thickness deviation but reduces inner surface roughness without significantly affecting inner diameter deviation. The study also found that a decrease in the initial inner wall roughness before pilgering results in improved final roughness. Under optimal conditions, the average inner surface roughness Sa can reach 0.177 μm, and small-diameter thick-walled seamless tubes with deviations in the inner diameter and wall thickness of 0.05 mm and 0.03 mm, respectively, are obtained. After tempering at 600 °C, the tensile strength (Rm) and yield strength (Rp0.2) of the cold-pilgered tube reach 1092 MPa and 947 MPa, respectively, and the elongation (δ5%) and impact energy (AkU) increase to 20.4% and 61.5 J, respectively.

21 April 2025 in Scientific Reports
Verified
Journal Article
Open access
PDF file
XDXiuping Ding
Xiuping Ding
XWXi Wang
Xi Wang
CZChenhui Zhu
Chenhui Zhu
JHJinMeng Hu
JinMeng Hu
MXMinheng Xu
Minheng Xu
JHJinfeng Huang
Jinfeng Huang
Thermal runaway represents a critical factor of catastrophic failure in power battery systems, posing significant safety risks in electric vehicle applications. Aluminum alloy casings serve as a primary protective barrier, and comprehensive investigation of their combustion characteristics is crucial for mitigating potential safety hazards in lithium-ion battery systems. The present study systematically examines the influence of dimensional variations and flame-retardant Ni-based surface modifications on the combustion mechanisms of 5052 aluminum alloy employed in lithium-ion battery configurations. Experimental findings reveal that the ignition temperature of the aluminum alloy decreased with oxygen pressure increased. The application of Ni-based flame-retardant coating markedly increasing the ignition threshold to 1007.8 ± 18.8 K. A robust predictive model characterizing the combustion threshold of the aluminum alloy and its flame-resistant coating was developed, demonstrating exceptional statistical validity with R2 values consistently exceeding 0.95. Microscopic morphological analysis of the combustion zones revealed that the incorporation of flame-retardant coating facilitates the formation of a more comprehensive oxide film and denser solidification zone microstructure.

3 November 2026 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
YLYu Liu
Yu Liu
CLChuansu Luo
Chuansu Luo
ZLZhuo Li
Zhuo Li
MMMinyu Ma
Minyu Ma
JJJinchao Jiao
Jinchao Jiao
YMYanlong Ma
Yanlong Ma