The mechanical properties and seepage characteristics of gas-bearing coal evolve with changes in the loading pattern, which could reveal the evolution of permeability in a protected coal seam and allow gas extraction engineering work to be designed by using the effect of mining multiple protective seams. Tests on gas seepage in raw coal under three paths (stepped-cyclic, stepped-increasing-cyclic, and crossed-cyclic loading and unloading) were carried out with a seepage tester under triaxial stress conditions. The permeability was subjected to the dual influence of stress and damage accumulation. After being subjected to stress unloading and loading, the permeability of coal samples gradually decreased and the permeability did not increase before the stress exceeded the yield stage of the coal samples. The mining-enhanced permeability of the coal samples in the loading stage showed a three-phase increase with the growth of stress and the number of cycles and exhibited an N-shaped increase under the stepped-cyclic loading while it linearly increased under the other two paths in the unloading stage. With the increase of peak stress and the accumulation of damage in coal samples, the sensitivity of the permeability of coal samples to stress gradually declined. The relationship between the damage variable and the number of cycles conformed to the Boltzmann function.
Landslide induced by underground mining is the main type of geological disaster in Guizhou Province. The spatial position of the mined‐out area is the key factor affecting the deformation evolution of mining landslides. Three typical mining‐induced slopes in western Guizhou Province are selected to establish the engineering geological model. The orthogonal experimental design is carried out with the position of the mined‐out area relative to the slope shoulder (PM) and the slope height (SH) as variables, and the discrete element simulation test is carried out. The influence of the two variables on the evolution of overlying strata fractures and the structure of slope surface deformed rock mass is analyzed by gray relational method. The results show that under the effect of mining, the overlying strata rock on the mined‐out area gradually collapses and produces cracks through the surface. The force chain arch gradually develops from the lower part to the surface rock layer, and the slope surface rock layer is transformed from a cantilever beam embedded at one end to a multisegment articulated beam. Depending on the number of segments of the articulated beam structure, it can be divided into three categories, and the rock mass where the slope collapse occurs is mainly concentrated at the end of the multisegment articulated beam. The central subsidence of the subsidence basin, the length of the end of the articulated beam, the position of the fulcrum, and the rotation angle of the beam structure are the key indicators affecting the stability of the multisegment articulated beam. Gray relational analysis shows that PM is the primary factor to control the output of these indicators. The multiple linear regression model of gray relational degree between PM and SH was constructed, and the prediction formula of gray relational grade was obtained, which realized the multiobjective prediction of the overlying strata rock structure model under the same slope parameters. The results provide the theoretical basis for disaster prevention and mitigation of gently inclined layered mining slopes.
The problem of surface deformation caused by coal mining is acute and usually lasts for a long time. During coal mining, the movement of the overlying strata has a broad range of influences, which may cause surface deformation, surface cracking, and damage to structures (buildings). However, continuous deformation monitoring data are often scarce in practice, making it challenging to predict the surface deformation caused by coal mining. In this context, this paper takes Sichuan’s Guanshan coalfield as the research object and proposes a comprehensive method integrating interferometric synthetic aperture radar (InSAR) technology, the FLAC3D finite difference software, and the probability integral method to predict the surface deformation caused by mining a thin seam of coal. The results show that the trend of surface deformation estimated by the numerical simulation agrees well with the results of InSAR data and the probability integral model when using InSAR historical deformation data to invert the parameters of rock mechanics in the numerical simulation, which is beneficial to improving the reliability of the simulation results. The calculations of the probability integral method are close to the predictions of the FLAC3D numerical simulation, and a settlement deformation of 0.68 m is expected to occur in the Guanshan coalfield area. The comprehensive prediction method proposed in this paper effectively enhances the accuracy of surface deformation prediction under the action of mining and can provide a reference for predicting the surface subsidence of similar coal mines.