Downhole high-temperature environment is an important factor affecting the performance of downhole electronic system. At present, various active cooling technologies and passive cooling technologies have been proposed to reduce the temperature of downhole electric circuit system. However, passive cooling technologies can only provide limited cooling capacity for drilling tools under high-temperature environment, and the duration of cooling is short, which cannot meet the long-time drilling task. This paper presents an active cooling system (ACS) for downhole electronics and the effects of different temperatures on the performance of electronic components are analyzed. The ACS mainly includes a micro supercharger, condenser tube, evaporation pipe, capillary tube, and refrigerant. The theoretical analysis of heat transfer and refrigerant capacity in high-temperature environment is carried out. The thermal characteristics of the ACS are evaluated experimentally. The results show that the temperature of electronic components can be reduced to below 163 °C in the 200 °C downhole environment and components. The geomagnetic field data measured by electronic components at room temperature, 200 °C and with ACS are compared. The results show that ACS can keep electronic components working normally.
1 September 2023 in Russian Journal of Nondestructive Testing
In this paper, we use ultrasonic detection to study the feature extraction and pattern recognition of defects in wellhead devices and to classify the depth of defects in wellhead devices. Firstly, we use COMSOL finite element software to simulate the ultrasonic defect detection process, and set up defects of different depths in the inner wall of the inspected object, through which we can observe the propagation process of ultrasonic waves in the pipe and get the simulation echo signal of defects with different depths. Build an experimental platform, set up artificial defects of different depths in the inner wall of the pipe, and collect each defect waveform. For the denoising of the defect echoes, this paper uses the empirical mode decomposition (EMD) denoising method, wavelet packet decomposition for energy entropy feature extraction, and finally the extracted feature vectors are fed into the random forest classifier optimized by the sparrow algorithm for pattern recognition, and compared with the unoptimized random forest classifier, the results show that for the ultrasonic simulation signals with different defect depths, the results show that the recognition accuracy of SSA-RF classifier can be as high as 92.5% for ultrasonic simulation signals with different defect depths; for ultrasonic real data, the recognition accuracy of SSA-RF can reach 89.5833% for man-made defects with different depths.
Downhole instrumentation requires more and more accuracy of MEMS inertial sensors. However, in measurement while drilling, temperature drift phenomenon of the sensor will have a cumulative impact on the drill pipe attitude solution. After experimental testing, the output response of the accelerometer had strong local linear and global nonlinear characteristics. In this paper, we proposed a temperature compensation model based on tent chaotic mapping and sparrow search algorithm optimized back propagation (BP) neural network (Tent-SSA-BPNN). Sparrow search algorithm (SSA) was optimized by tent chaotic mapping, which was utilized to improve the uniformity and search ability of SSA populations. Then, the improved SSA was used to optimize the weight and bias parameters of the BP neural network for constructing the temperature compensation model. Finally, the trained compensation model is integrated into the microprogram control unit for real-time compensation testing. The experimental results show that after sacrificing a small amount of sampling frequency, the compensation model proposed in this article has good global compensation performance, and the mean absolute percentage error is reduced from 2% to 0.2% compared to the original output. The mean absolute error and root mean square error of the improved compensation model are all reduced compared to the pre-improved BP compensation model. This temperature-compensated modeling method has a reference value for low-cost and high-precision modeling in high temperature environments, while greatly saving time cost and measurement costs.
The addition of a polymer to the jet medium enhances its ability to break rock, and the structure of the nozzle plays a vital role in the full utilization of energy. In this paper, a self-propelled porous jet bit with a support plate is designed, which can prevent the drill bit from jamming due to the jet nozzle against the bottom of the well during the drilling process. And the structural design of the cone-converging nozzle is applied to the forward center nozzle. The polymer additive jet flow field and the pure water jet flow field were compared by numerical simulation and experimental investigation. The results show that the polymer additive jet has a longer isokinetic core, and the rock-breaking volume of the polymer additive jet is much larger than that of the pure water jet, and the optimal spray distance is increased. The forward central jet with the conical convergent nozzle structure has more efficient rock-breaking ability.
25 February 2025 in Nondestructive Testing and Evaluation