During vehicle operation, lateral tire forces generally require a finite time to reach their steady-state values, and this dynamic response can be characterized by the tire relaxation length. For an active front steering (AFS) vehicle equipped with a mechanical elastic wheel (MEW), an MPC-based control strategy is developed to account for this delayed tire response and improve handling stability. The front steering angle is selected as the control input, while a first-order lag formulation is incorporated into the prediction model to represent the transient evolution of lateral tire forces. To accommodate variations in tire response, the lateral relaxation length is estimated online using an unscented Kalman filter (UKF). The lateral tire forces are calculated using the Magic Formula tire model, which describes the nonlinear relationship between tire forces and slip conditions. To reduce the computational burden associated with online optimization, the tire model is linearized around the current operating point before being used in the controller. To examine the robustness of the UKF estimator under vehicle parameter uncertainty, a 20% increase in vehicle mass is applied. The proposed control method is then assessed in three simulation scenarios, with a conventional MPC controller and an LQR controller serving as benchmarks. Although the vehicle mass is perturbed, the estimated lateral relaxation lengths of the front and rear axles follow broadly similar variation patterns. The simulation results also show that the proposed method achieves improved yaw rate tracking and sideslip angle regulation compared with conventional MPC, thereby enhancing vehicle handling stability.
High-speed traction motors in electric vehicles (EVs) subject their support bearings to severe mechanical and thermal loads. Bearing skidding and frictional heat generation can cause abnormal temperature rises, whereas uncertainty in convective heat transfer coefficients limits the accuracy of thermal simulations. This study investigates the skidding dynamics and temperature field of a motor deep-groove ball bearing (DGBB). A 35-degree-of-freedom dynamic model is established using the lumped-mass method to analyze rolling-element contact, skidding, and cage collisions at different speeds. A heat-generation and heat-transfer model is then developed based on bearing friction theory and moving-heat-source theory. The convective heat transfer coefficients are calibrated against measured temperatures using the non-dominated sorting genetic algorithm II (NSGA-II) within an integrated MATLAB–ANSYS framework, after which the temperature fields under constant- and variable-speed conditions are simulated. The results show that the rolling-element–raceway contact forces vary periodically, collisions between the rolling elements and cage are intermittent, and increasing speed intensifies the contact-force fluctuation and the ball–cage impacts and raises the skidding velocity, although the skidding ratio decreases. The component temperatures decrease in the order inner ring, rolling elements, outer ring and cage, and respond dynamically to changes in speed and load. The time-averaged cage speed agrees with the theoretical value to within 1% over 1000–10,000 rpm, and the calibrated thermal model reproduces the measured ring temperatures to within about 2 °C. The findings provide a useful reference for temperature prediction and thermal management of EV motor bearings.
As the core rotating components of the air supply system, the compressor and its blades are prone to crack initiation under long-term cyclic loading and high-temperature erosion. Failure to detect cracks in a timely manner may lead to blade fracture, subsequently causing catastrophic unit failure. Affected by environmental noise and the weak vibration signatures of blade cracks, the existing methods for detecting blade cracks lack sufficient accuracy and reliability. To address this problem, a cracked blade detection method is proposed based on a vibration deep fusion framework for compressors. Specifically, the proposed vibration deep fusion framework includes two parts, namely data-level and decision-level fusion. The proposed data-level fusion method divides the original vibration signals into low-frequency and high-frequency bands based on the sampling frequencies of the two vibration sensors and fuses these two frequency bands to suppress noise and enhance defect features. Moreover, the proposed decision-level fusion method can further fuse the preliminary results obtained from the one-dimensional convolutional neural network with two raw vibration signals and the data-level fusion signal, thereby obtaining the final blade crack detection result. To verify the proposed method, a compressor blade crack detection experimental platform is built to simulate the crack detection effect of blades under different working conditions, which covers blades with artificial cracks of different lengths in noisy and noiseless environments. The results show that the proposed method has a detection accuracy of over 96% with 10-fold cross-validation, and the ablation experiment verifies that the proposed method is superior to traditional single signal or single-stage fusion methods, which demonstrates its effectiveness for compressor blade crack detection.
Conventional thermal protection strategies for electromechanical compound transmission systems rely mainly on temperature thresholds and segmented power derating, resulting in reactive intervention and excessive power loss under prolonged overload and deteriorating cooling conditions. The proposed strategy treats thermal protection as a prediction-to-action problem: future temperatures of multiple critical components are estimated by an incrementally updated Neural ODE and incorporated, together with current thermal and operating states, into a PPO policy that outputs a continuous derating factor. This formulation enables one control decision to account for competing thermal risks while retaining vehicle power demand. The proposed framework is deployed on a physical controller and validated through controller hardware-in-the-loop experiments under multiple overheating scenarios. The temperature prediction RMSE remains below 0.43 °C. The temperature prediction model maintains good accuracy on previously learned conditions and reduces the average RMSE and MAPE by 16.71% and 9.91%, respectively, compared with LSTM. The closed-loop evaluation compares PPO with static stepwise derating, fixed-rate linear ramp derating, MPC, and SAC, together with a reference case without active derating. The experimental results show that, under eight representative thermal-risk scenarios, the PPO-based strategy can intervene proactively according to the system thermal state and continuously adjust the derating level, thereby effectively suppressing the temperature rise of the motor windings, bearings, and controller. Compared with static derating, the PPO-based strategy increases the NTSM by 0.0545–0.2094 and reduces the ITRI by 6.3–26.0%. The PDSR increases by 3.24–9.51 percentage points in five operating conditions, while decreasing by 2.82–2.88 percentage points in three high-speed-related conditions. Overall, the proposed strategy reduces the thermal risks of critical components and enlarges the thermal safety margin while balancing thermal safety and vehicle power demand.