Casing shear deformation has become a serious problem in the development of shale gas fields, which is believed to be related to fault slipping caused by multistage fracturing, and the evaluation of the reduction of a casing’s inner diameter is key. Although many fault slipping models have been published, most of them have not taken the fluid-solid-heat coupling effect into account, and none of the models could be used to calculate the reduction of a casing’s inner diameter. In this paper, a new 3D finite element model was developed to simulate the progress of fault slipping, taking the fluid-solid-heat coupling effect during fracturing into account. For the purpose of increasing calculation accuracy, the elastoplastic constitutive relations of materials were considered, and the solid-shell elements technique was used. The reduction of the casing’s inner diameter along the axis was calculated and the calculation results were compared with the measurement results of multi-finger caliper (MFC) surveys. A sensitivity analysis was conducted, and the influences of slip distance, casing internal pressure, thickness of production and intermediate casing, and the mechanical parameters of cement sheath on the reduction of a casing’s inner diameter in the deformed segment were analyzed. The numerical analysis results showed that decreasing the slip distance, maintaining high pressure, decreasing the Poisson ratio of cement sheath, and increasing casing thickness were beneficial to protect the integrity of the casing. The numerical simulation results were verified by comparison to the shape of MFC measurement results, and had an accuracy up to 90.17%. Results from this study are expected to provide a better understanding of casing shear deformation, and a prediction method of a casing’s inner diameter after fault slipping in multistage fracturing wells.

Continuous gas leakage paths of cement sheath during hydraulic fracturing were investigated in this study. The finite‐element models of a casing–cement‐sheath–formation assembly for the whole wellbore were established, the integrity of the cement sheath of the whole wellbore during single‐stage fracturing was analyzed firstly, and the factors affecting the integrity were examined. Furthermore, a cyclic compression test was conducted. Then, test results for the accumulative plastic strain of the cement sheath under the intermediate casing shoe during multistage fracturing were analyzed. Finally, the mechanism of dilatancy of cement stone in cyclic compression tests was analyzed. The results show that the radial and tangential stresses of the cement sheath increase and decrease, respectively, with depth. The cement sheath above the intermediate casing shoe had a risk of tensile failure, which could result in tangential tensile cracks. The cement sheath below the intermediate casing shoes had cumulative plastic strain, resulting in a microannulus. Reducing Young's modulus, increasing the Poisson ratio of the cement sheath, and reducing the pump pressure were beneficial to relieve the stress state. When the cyclic compressive stress exceeded the dilatation yield stress, the permeability increased with cycle numbers, and the increase in permeability provided another leakage path for gas migration.

Based on the 150 collected experimental data points, the accuracy of the four thermodynamic models in predicting the phase equilibrium of the gas hydrate was compared.

The purpose of this paper is to discuss the variation of wellbore temperature and bottom-hole pressure with key factors in the case of coupled temperature and pressure under multi-pressure system during deep-water drilling circulation. According to the law of energy conservation and momentum equation, the coupled temperature and pressure calculation model under multi-pressure system is developed by using the comprehensive convective heat transfer coefficient. The model is discretized and solved by finite difference method and Gauss Seidel iteration respectively. Then the calculation results of this paper are compared and verified with previous research models and field measured data. The results show that when the multi-pressure system is located in the middle formation, the temperature of the annulus corresponding to location of the system is the most affected, and the temperature of the other areas in annulus is hardly affected. However, when the multi-pressure system is located at the bottom hole, the annulus temperature is greatly affected from bottom hole to mudline. In addition, the thermo-physical parameters of the drilling fluid can be changed by overflow and leakage. When only overflow occurs, the annulus temperature increases the most, but the viscosity decreases the most. When only leakage occurs, the annulus temperature decreases the most and the viscosity increases the most. However, when the overflow rate is greater than the leakage rate, the mud density and bottom-hole pressure increase the most, and both increase the least when only leakage occurs. Meanwhile, bottom-hole pressure increases with the increase of pump rate but decreases with the increase of inlet temperature. The research results can provide theoretical guidance for safe drilling in complex formations such as multi-pressure systems.

To eliminate or reduce stick–slip vibration in torsional vibration of the drilling string and improve the rate of penetration (ROP), a stick–slip vibration model of the drilling string considering the ROP was established based on the multidimensional torsional vibration model of the drilling string. The model was verified by simulation analysis. The characteristics of the drilling string stick–slip vibration in the three stages of stationary, slip, and stick were analyzed. This paper investigated the influence of rotary torque, rotary speed, and weight on bit (WOB) on stick–slip vibrations in the drill string. Based on this, the relationship between the drilling parameters and ROP was established. Drilling parameter optimization was completed for soft, medium-hard, and hard formations. Results showed that appropriately increasing torque and decreasing WOB can reduce or even eliminate stick–slip vibrations in the drill string and increase the ROP. The parameter optimization increased the ROP by 11.5% for the soft formation, 13.7% for the medium-hard formation, and 14.3% for the hard formation. The established drill string stick–slip vibration model provides theoretical guidance for optimizing drilling parameters in different formations.