Yanjun Zhao

Mrs. Yanjun Zhao

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2021 in Materials Research Express
Verified
Journal Article
Open access
YZYanjun Zhao
Yanjun Zhao
LLLiuyang Li
Liuyang Li
ZLZepeng Lu
Zepeng Lu
GTGuanqi Teng
Guanqi Teng
SLShaochen Liu
Shaochen Liu
AHAoping He
Aoping He
In the research a commercial pure aluminium was cold rolled by 98% accumulative severe plastic deformation and then ultra-fast annealed at 350 °C−520 °C with the 1000 °C/s heating rate and 1.0 s holding time. The microstructure evolution and the mechanisms of the recovery and recrystallization for the above ultra-fast annealed pure aluminium were analyzed by Gleeble 3500 thermal simulation system, electron backscatter diffraction(EBSD),and transmission electron microscopy (TEM). For the ultra-fast annealing pure aluminum, the grain size increases from 2.05 μm to 17.10 μm with the increase of annealing temperature from 410 °C to 520 °C; the tensile strength of the annealed pure aluminium decreases from 116.48 MPa to 53.43 MPa, and the uniform elongation increases from 1.20% to 39.78%. When annealing at 410 °C, the storage energy was transformed into the driving force for grain nucleation, which greatly refined the grains. When annealing at 380 °C ∼ 410 °C, the pure aluminium is in the stage of recrystallization, and the average grain size refined to 2.05 μm. When annealing at 435 °C, the number of small-angle grain boundaries (<15°) was significantly reduced and the number of large-angle grain boundaries increased. When the annealing temperature increased to 470 °C or 520 °C, the crystalline grains had merged each other, leading to the grain size grow to 17.10 μm. The annealing temperature of ultra-fast annealing should be in the range of 410 °C to 435 °C for optimizing the mechanical performances of commercial pure aluminum.

8 April 2023 in Scientific Reports
Verified
Journal Article
Open access
PDF file
YZYanjun Zhao
Yanjun Zhao
YCYunfei Cao
Yunfei Cao
WWWeiying Wen
Weiying Wen
ZLZepeng Lu
Zepeng Lu
JZJingrui Zhang
Jingrui Zhang
PCPeilin Chen
Peilin Chen
Low Ni alumina-forming austenitic (AFA) heat-resistant steel is an advanced high-temperature stainless steel with reduced cost, good machinability, high-temperature creep strength, and high-temperature corrosion resistance. Using the First-principles approach, this study examined the effect of Mn content on austenite stability and mechanical properties at the atomic level. Adding Mn to low Ni-AFA steel increases the unit cell volume with an accompanying increase in the absolute value of formation energy; the austenite formed more easily. The austenitic matrix binding energy decreases and remains negative, indicating austenite stability. As the Mn content increases from 3.2 to 12.8 wt%, the system's bulk modulus (B) rises significantly, and the shear modulus (G) falls. In addition, the system's strength and hardness decrease, and the Poisson ratio of the austenite matrix increases with improved elasticity; the system has excellent plasticity with an increase in the B/G. For the Fe22–Cr5–Ni3–Al2 system, with the increase of Mn content, the electron density distribution between the atoms is relatively uniform, and the electrons around the Mn atoms are slightly sparse, which will slightly reduce the structural stability of the matrix. The experiment demonstrated the matrix maintains the austenitic structure when adding 3.2–12.8 wt% Mn elements to low Ni-AFA steel. At an Mn content of 8 wt%, the overall mechanical properties of the high-Mn AFA steel are optimal, with a tensile strength of 581.64 MPa, a hardness of 186.17 HV, and an elongation of 39%.

16 April 2019 in Metals
Verified
Journal Article
Open access
PDF file
Zhiping XiongZhiping Xiong
Zhiping Xiong
Andrii KostryzhevAndrii Kostryzhev
Andrii Kostryzhev
YZYanjun Zhao
Yanjun Zhao
Elena PerelomaElena Pereloma
Elena Pereloma
Instead of conventional steel making and continuous casting followed by hot and cold rolling, strip casting technology modified with the addition of a continuous annealing stage (namely, modified strip casting) is a promising short-route for producing ferrite-martensite dual-phase (DP) and multi-phase transformation-induced plasticity (TRIP) steels. However, at present, the multi-phase steels are not manufactured by the modified strip casting, due to insufficient knowledge about phase transformations occurring during in-line heat treatment. This study analysed the phase transformations, particularly the formation of ferrite, bainite and martensite and the retention of austenite, in one 0.17C-1.52Si-1.61Mn-0.195Cr (wt. %) steel subjected to the modified strip casting simulated in the laboratory. Through the adjustment of temperature and holding time, the characteristic microstructures for DP and TRIP steels have been obtained. The DP steel showed comparable tensile properties with industrial DP 590 and the TRIP steel had a lower strength but a higher ductility than those industrially produced TRIP steels. The strength could be further enhanced by the application of deformation and/or the addition of alloying elements. This study indicates that the modified strip casting technology is a promising new route to produce steels with multi-phase microstructures in the future.

19 February 2021 in Metals
Verified
Journal Article
Open access
PDF file
YZYanjun Zhao
Yanjun Zhao
HDHaochen Ding
Haochen Ding
YCYunfei Cao
Yunfei Cao
PCPeilin Chen
Peilin Chen
ZHZhiliu Hu
Zhiliu Hu
LLLingxiao Li
Lingxiao Li
The high one-pass deformation behaviors of mass-produced Al–4.30Mg alloy are investigated in the temperature ranging of 350 °C–500 °C, the strain rate ranging of 0.01 s−1–1 s−1 and the reduction ranging of 50–75%. 3D processing maps are constructed by the superimposition of the instability map and the power dissipation map at the true strain of 0.69, 0.92, 1.20 and 1.38. When the true strain increases from 0.69 to 1.38, the average apparent activation energy (Q) decreases from 140.3 kJ/mol to 112.7 kJ/mol, indicating the reduction of the hot deformation energy barrier. The heating caused by a large strain of 1.38 greatly reduces the Q and improves processing efficiency. The instability regions at the strain of 0.69 appear at two domains, namely 350 °C/1.0 s−1 and 450 °C/1.0 s−1; whereas, the instability regions disappear at the strain of 1.38. The maximum efficiency of power dissipation is about 48%, which occurs at both domains of 440–480 °C/0.01 s−1/0.69 true strain and 470–500 °C/1.0 s−1/1.20 true strain. High-efficiency domains represent the optimized deformation conditions which are verified by stress-strain curves and microstructure characterization, in which the local dynamic recrystallization is observed and the power dissipates mainly by dynamic recrystallization during deformation.

11 February 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
ZHZhiliu Hu
Zhiliu Hu
ZWZongfan Wei
Zongfan Wei
BHBaoyu Hou
Baoyu Hou
YZYanjun Zhao
Yanjun Zhao
XPXingzhi Pang
Xingzhi Pang
LLLingxiao Li
Lingxiao Li

1 March 2019 in Strength of Materials
Verified
Journal Article
Closed access
PDF file
YZYanjun Zhao
Yanjun Zhao
YSY. M. Su
Y. M. Su
MLM. Liu
M. Liu
ZHZ. L. Hu
Z. L. Hu
Peng TangPeng Tang
Peng Tang