ASHRAF ALI

Prof. ASHRAF ALI

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2011 in Applied Nanoscience
Verified
Journal Article
Open access
PDF file
AAASHRAF ALI
ASHRAF ALI
AAAwad Kh. Al-Asmari
Awad Kh. Al-Asmari
Wet electrospinning of polyacrylonitrile (PAN) and dimethylformamide (DMF) with copper nanoparticles (CuNP) at different concentrations from 0.2 to 1 wt% have been studied under certain spinning conditions. A specific coagulating water bath has been used to collect different fibroses and fibril diameters, the effect of spinning height on the produced nanofiber and CuNP/PAN nanofibril composites have been studied from 1 to 7 cm heights. A minimum average diameter of 64 nm has been reported at 7-cm spinning height. Two heat treatment steps have been used to enhance the electrical properties of CuNP/PAN nanofibril composites. SEM has been used to study the morphological characteristics of the electrospun nanofibroses membranes. Preliminary electrical measurements using 4-point probing system showed a noticeable improvement in the electrical conductivity of the produced nanofibril composite membranes. Also, electrical property of a single CuNP/carbon nanofibril composite has been theoretically calculated based on Lichtenecker formula. The produced membranes have been used to build a micro surface-mounted components (MSMC) such as Micro Field Effect Transistor (MFET). A high transconductance has been reported for such a device which will open the door for many promising applications especially in Electronics and Biomedicine .

11 February 2020 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
SSsaleh sobhy
saleh sobhy
SZSaid H Zoalfakar
Said H Zoalfakar
MAMa Agwa
Ma Agwa
AAASHRAF ALI
ASHRAF ALI
Basalt fiber was first treated in a mixture of formic acid (FA) and dichloromethane (DCM) to reduce its diameter down to one micrometer. Electrospinning process was utilized to produce treated basalt fiber (TBF)-reinforced nylon 6,6/epoxy (NY/EP) hybrid nanofibril composites. NY/EP polymers have been dissolved in 80:20 mixture of FA/DCM solvent to form a homogenous solution. TBFs with different weight ratios of 5, 10, 15, 20, and 25 wt% were added to NY/EP (ratio of 5:1). The morphology of the hybrid nanocomposites was investigated by scanning electron microscopy and their compositions were analyzed using energy-dispersive X-ray spectroscopy. The thermal properties were studied by differential scanning calorimetry and thermogravimetric analysis. The mechanical properties of the hybrid nanocomposites, including tensile strength and modulus, are improved with respect to NY/EP hybrid nanofibers. An increase of 76% and 87% in tensile strength and Young’s modulus was acquired, respectively, at 15 wt% of TBF. Also, the addition of TBF increased the thermal stability of nanofibril composites.

1 June 2022 in Journal of Industrial Textiles
Verified
Journal Article
Open access
SSsaleh sobhy
saleh sobhy
MAMahmoud Mohamed Atta
Mahmoud Mohamed Atta
AMAa Megahed
Aa Megahed
KAKa Abu-Hasel
Ka Abu-Hasel
MAMohammed Alquraish
Mohammed Alquraish
SZSaid H Zoalfakar
Said H Zoalfakar
The present work is an attempt to model the diameter of Poly Lactic-co-Glycolic Acid (PLGA) nanofibers by utilizing response surface methodology (RSM) and artificial neural networks (ANNs). Hence, determining the optimal electrospinning process conditions to produce a minimum fiber diameter. For modelling the average diameter of nanofibers, RSM approach based on four parameters (polymer concentration, high voltage and needle tip to collector distance and spinning angle) with five-level was compared to ANN technique. In the RSM approach, central composite design (CCD) was used to determine the individual and interaction impacts of the parameters on the average diameter of nanofibers. Several ANNs of single and double hidden layers with different number of cells for each were tried to obtain the best network structure. The experimental and predicted PLGA fiber diameters using an ANN showed a strong correlation, indicating that the network topology of 4-14-1 has good predictability for analyzing factors impacting PLGA fiber diameter. The average absolute relative error for predicting PLGA nanofibers’ diameter using ANN (2.24%) is slightly less than that obtained from RSM (2.59%). The high regression coefficient between the variables and the response (R2 = 0.9636) shows a good second-order polynomial regression model for evaluating experimental data. The R2 value was 0.945, indicating that the ANN model was good fitting with the experimental results. The optimum combinations (PLGA concentration of 26 wt.%, high voltage 22 kV, needle tip to collector distance 20 cm, and spinning angle 60o) were developed by RSM model for electrospinning PLGA nanofiber that can produce fine, consistent, and high-quality nanofibers.

16 March 2021 in Polymers
Verified
Journal Article
Open access
PDF file
Mohamed KchaouMohamed Kchaou
Mohamed Kchaou
MAMohammed Alquraish
Mohammed Alquraish
KAKhaled Abuhasel
Khaled Abuhasel
Ahmad AbdullahAhmad Abdullah
Ahmad Abdullah
AAASHRAF ALI
ASHRAF ALI
Over the last twenty years, researchers have focused on the potential applications of electrospinning, especially its scalability and versatility. Specifically, electrospun nanofiber scaffolds are considered an emergent technology and a promising approach that can be applied to biosensing, drug delivery, soft and hard tissue repair and regeneration, and wound healing. Several parameters control the functional scaffolds, such as fiber geometrical characteristics and alignment, architecture, etc. As it is based on nanotechnology, the concept of this approach has shown a strong evolution in terms of the forms of the materials used (aerogels, microspheres, etc.), the incorporated microorganisms used to treat diseases (cells, proteins, nuclei acids, etc.), and the manufacturing process in relation to the control of adhesion, proliferation, and differentiation of the mimetic nanofibers. However, several difficulties are still considered as huge challenges for scientists to overcome in relation to scaffolds design and properties (hydrophilicity, biodegradability, and biocompatibility) but also in relation to transferring biological nanofibers products into practical industrial use by way of a highly efficient bio-solution. In this article, the authors review current progress in the materials and processes used by the electrospinning technique to develop novel fibrous scaffolds with suitable design and that more closely mimic structure. A specific interest will be given to the use of this approach as an emergent technology for the treatment of bacteria and viruses such as COVID-19.

17 June 2014 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
AAASHRAF ALI
ASHRAF ALI
AEA. R. Eldesouky
A. R. Eldesouky
SZSaid H. Zoalfakar
Said H. Zoalfakar

13 January 2021 in Polymer Composites
Verified
Journal Article
Closed access
PDF file
AFA. S. Fayed
A. S. Fayed
KAK. A. Abu‐Hasel
K. A. Abu‐Hasel
SMSameh M. Mahdy
Sameh M. Mahdy
AAASHRAF ALI
ASHRAF ALI