Airborne particulate matter emitted from motor vehicle brakes is a contributor to urban air quality. Therefore, a method to rank brake pairs (pads and rotors) with respect to their particle emission factors in a reliable way is needed to develop a low-emission disc brake. A novel inertial disc brake dynamometer designed for brake particle emission studies, a modified SAE J 2707 cycle, an electrical low-pressure cascade impactor and a filter are used to test five different pad materials against cast-iron rotors. By changing only the pad materials, it is shown that the differences between the mass emission factor and the number emission factor of the the worst brake pair and those of the best brake pair decreases by more than four times and 19 times respectively. Furthermore, the results show that the material combination ranked the best in terms of the mass emission factor is ranked the worst in terms of the number emission factor. The results reveal that this combination of a test stand, a test cycle and particle instruments can discriminate between different brake pair materials in a reliable way in the case of the mass emission factors while more research has to be carried out in the case of the number emission factors.

Brake-related airborne particulate matter contributes to urban emissions in the transport sector. Recent research demonstrated a clear dependence of the number of ultra-fine particles on the disc brake temperature. Above the so-called transition temperature, the number of ultra-fine particles increases dramatically (several magnitudes). As for exhaust emissions, part of the emissions released during braking can be in the volatile fraction. For this reason, a disc brake test stand specifically designed for aerosol research was equipped with three different aerosol sampling instruments: (i) a standard cascade impactor, (ii) a cascade impactor operating at high temperature with a heated sampling line, and (iii) a standard cascade impactor with a thermodenuder. Tests with a brake assembly representative of European passenger vehicles were executed, and the concentration of released airborne particles was determined. The results showed a decrease by several magnitudes in the concentration (in the size range of below 200 nm) using the cascade impactor operating at 180 °C with the sampling line heated to 200 °C. A further decrease in the concentration of airborne particles with size fractions below 200 nm was measured using a standard cascade impactor with a thermodenuder heated to 300 °C.

Brake-related particulate matter contributes considerably to the non-exhaust emissions of the transport sector in urban areas of the world. The airborne particle emissions from automotive brakes currently lack any proper regulations. Future regulations require test stands, test cycles and particle instruments to be suitable for measuring the brake emissions. This present work focuses on the design of a novel test stand for reliable measurements of the brake emissions with a high sampling efficiency. A test stand in the form of an inertial disc brake dynamometer was redesigned to allow control of the cleanness of the incoming air and to assure isokinetic sampling. The cleanness of the incoming air, together with an over-pressurized chamber around the brake assembly, ensures that all the particles measured originate from the brake materials. In order to evaluate the novel design, the number and size distributions of the brake emissions are measured online with and without control of the cleanness of the intake air. The results reveal that this test stand can be proposed as a standard test stand to assess objectively the emissions of airborne brake particles in future regulations.

The relative contribution of brake emissions to traffic-induced ambient Particulate Matter (PM) concentrations has increased over the last decade. Nowadays, vehicles’ brakes are recognised as an important source of non-exhaust emissions. Up to now, no standardised method for measuring brake particle emissions exists. For that reason, the Particle Measurement Programme (PMP) group has been working on the development of a commonly accepted method for sampling and measuring brake particle emissions. The applied braking cycle is an integral part of the overall methodology. In this article, we present the results of an interlaboratory study exploring the capacity of existing dynamometer setups to accurately execute the novel Worldwide Harmonised Light-Duty Vehicles Test Procedure (WLTP)–brake cycle. The measurements took place at eight locations in Europe and the United States. Having several dynamometers available enabled the coordination and execution of the intended exercise, to determine the sources of variability and provide recommendations for the correct application of the WLTP–brake cycle on the dyno. A systematic testing schedule was applied, followed by a thorough statistical analysis of the essential parameters according to the ISO 5725 standards series. The application of different control programmes influenced the correct replication of the cycle. Speed control turned out to be more accurate and precise than deceleration control. A crucial output of this interlaboratory study was the quantification of standard deviations for repeatability (between repeats), sample effect (between tests), laboratory effect (between facilities), and total reproducibility. Three critical aspects of the statistical analysis were: (i) The use of methods for heterogeneous materials; (ii) robust algorithms to reduce the artificial increase in variability from values with significant deviation from the normal distribution; and (iii) the reliance on the graphical representation of results for ease of understanding. Even if the study of brake emissions remained out of the scope of the current exercise, useful conclusions are drawn from the analysis of the temperature profile of the WLTP–brake cycle. Urban braking events are generally correlated to lower disc temperature. Other parameters affecting the brake temperature profile include the correct application of soak times, the temperature measurement method, the proper conditioning of incoming cooling air and the adjustment of the cooling airspeed.

Particulate matter emission factors from vehicle brakes are difficult to assess directly from the field. Moreover, there is a lack of a standardized cycle and test stand for evaluating brake emissions. For these reasons, a test cycle was developed from real driving data collected from a car. This new test cycle was implemented on an inertia disc brake dynamometer appositely designed for brake particle emission studies. Results reveal that, for the brake system used as an example, the obtained emission factors for the urban driving conditions studied are comparable to EURO 6 regulations in terms of particle number and comparable to EURO 4 levels in terms of mass with brake emission factors equal to 4.37–6.46 × 10¹¹ particles/km and 44–48 mg/km, respectively.