Shale oil and gas resources contribute significantly to the energy production in the U.S. Greenhouse gas emissions come from combustion of fossil fuels from potential sources of power plants, oil refineries, and flaring or venting of produced gas (primarily methane) in oilfields. Economic utilization of greenhouse gases in shale reservoirs not only increases oil or gas recovery, but also contributes to CO2 sequestration. In this paper, the feasibility and efficiency of gas injection approaches, including huff-n-puff injection and gas flooding in shale oil/gas/condensate reservoirs are discussed based on the results of in-situ pilots, and experimental and simulation studies. In each section, one type of shale reservoir is discussed, with the following aspects covered: (1) Experimental and simulation results for different gas injection approaches; (2) mechanisms of different gas injection approaches; and (3) field pilots for gas injection enhanced oil recovery (EOR) and enhanced gas recovery (EGR). Based on the experimental and simulation studies, as well as some successful field trials, gas injection is deemed as a potential approach for EOR and EGR in shale reservoirs. The enhanced recovery factor varies for different experiments with different rock/fluid properties or models incorporating different effects and shale complexities. Based on the simulation studies and successful field pilots, CO2 could be successfully captured in shale gas reservoirs through gas injection and huff-n-puff regimes. The status of flaring gas emissions in oilfields and the outlook of economic utilization of greenhouse gases for enhanced oil or gas recovery and CO2 storage were given in the last section. The storage capacity varies in different simulation studies and is associated with well design, gas injection scheme and operation parameters, gas adsorption, molecular diffusion, and the modelling approaches.
In this study, molecular dynamics (MD) simulation is used to investigate the phase behavior and composition distribution of an ethane/heptane binary mixture in heterogeneous oil-wet graphite nanopores with pore size distribution. The pore network system consists of two different setups of connected bulk and a 5-nm pore in the middle; and the bulk connected to 5-nm and 2-nm pores. Our results show that nanopore confinement influences the phase equilibrium of the multicomponent hydrocarbon mixtures and this effect is stronger for smaller pores. We recognized multiple adsorbed layers of hydrocarbon molecules near the pore surface. However, for smaller pores, adsorption is dominant so that, for the 2-nm pore, most of the hydrocarbon molecules are in the adsorbed phase. The MD simulation results revealed that the overall composition of the hydrocarbon mixture is a function of pore size. This has major implications for macro-scale unconventional reservoir simulation, as it suggests that heterogenous shale nanopores would host fluids with different compositions depending on the pore size. The results of this paper suggest that modifications should be made to the calculation of overall composition of reservoir fluids in shale nanopores, as using only one overall composition for the entire heterogenous reservoir can result in significant error in recovery estimations.
In this paper, we investigate the effect of pore size heterogeneity on fluid composition distribution of multicomponent-multiphase hydrocarbons and its subsequent influence on mass transfer in shale nanopores. The change of multi-contact minimum miscibility pressure (MMP) in heterogeneous nanopores was investigated. We used a compositional simulation model with a modified flash calculation, which considers the effect of large gas–oil capillary pressure on phase behavior. Different average pore sizes for different segments of the computational domain were considered and the effect of the resulting heterogeneity on phase change, composition distributions, and production was investigated. A two-dimensional formulation was considered here for the application of matrix–fracture cross-mass transfer and the rock matrix can also consist of different segments with different average pore sizes. Both convection and molecular diffusion terms were included in the mass balance equations, and different reservoir fluids such as ternary mixture syntactic oil, Bakken oil, and Marcellus shale condensate were considered. The simulation results indicate that oil and gas phase compositions vary in different pore sizes, resulting in a concentration gradient between the two adjacent pores of different sizes. Given that shale permeability is extremely small, we expect the mass transfer between the two sections of the reservoir/core with two distinct average pore sizes to be diffusion-dominated. This observation implies that there can be a selective matrix–fracture component mass transfer as a result of confinement-dependent phase behavior. Therefore, the molecular diffusion term should be always included in the mass transfer equations, for both primary and gas injection enhanced oil recovery (EOR) simulation of heterogeneous shale reservoirs.
In this research, data analytics and machine learning were used to identify the performance metrics of loaders and haul trucks during mining operations. We used real-time collected data from loaders and haul trucks operating in multiple quarries to broaden the scope of the study and remove bias. Our model indicates relationships between multiple variables and their impacts on production in an operation. Data analysis was also applied to ground engagement tools (GET) to identify key preventative maintenance schedules to minimize production impact from capital equipment downtime. Through analysis of the loader’s data, it was found there is an efficient cycle time of around 35 s to 40 s, which yielded a higher payload. The decision tree classifier algorithm created a model that was 87.99% accurate in estimating the performance of a loader based on a full analysis of the data. Based on the distribution of production variables across each type of loader performing in a similar work environment, the Caterpillar 992K and 990K were the highest-yielding machines. Production efficiency was compared before and after maintenance periods of ground engaging tools on loader buckets. With the use of maintenance and production records for these tools, it was concluded that there was no distinguishable change in average production and percentage change in production value before and after maintenance days.
27 February 2026 in Environmental Monitoring and Assessment
This work compares the mechanical properties of two geomaterials: forsterite and magnesite. Various physical conditions are considered to investigate the evolution of stress–strain relationships for these two polycrystals. A molecular-scale study is performed on three-dimensional models of forsterite and magnesite. Three different temperatures (300 K, 500 K, and 700 K) and strain rates (0.001, 0.01, and 0.05 ps−1) are considered to initiate deformation in the polycrystals under tensile and compressive forces. The polycrystalline structures face deformation at lower peaks at high temperatures. The Young’s modulus values of forsterite and magnesite are found to be approximately 154.7451 GPa and 92.84 GPa under tensile forces and these values are found to be around 120.457 GPa (forsterite) and 77.04 GPa (magnesite) for compressive forces. Increasing temperature reduces the maximum strength of the polycrystalline structures, but forsterite shows higher ductility compared to magnesite. Strain rate sensitivity and the effect of grain size are also studied. The yield strengths of the forsterite and magnesite drop by 7.89% and 9.09% when the grain size is reduced by 20% and 15%, respectively. This study also focuses on the changes in elastic properties for different pressures and temperatures. In addition, from the radial distribution function (RDF) results, it was observed that the peak intensity of pairwise interaction of Si–O is higher than that of Mg–O. Finally, it is found that the formation of magnesite, which is the product of mineral carbonation of forsterite, is favorable in terms of mechanical properties for the comminution process.