Mohammad Kazemi

Dr. Mohammad Kazemi

School of Engineering, Slippery Rock University of Pennsylvania, Slippery Rock, Pennsylvania, PA 16057, USA

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 January 2022 in Journal of Petroleum Science and Engineering
Verified
Journal Article
Closed access
STSam Takbiri
Sam Takbiri
Mohammad KazemiMohammad Kazemi
Mohammad Kazemi
ATAli Takbiri-Borujeni
Ali Takbiri-Borujeni
JMJason McIlvain
Jason McIlvain

15 June 2023 in Computers & Fluids
Verified
Journal Article
Closed access
Mohammad KazemiMohammad Kazemi
Mohammad Kazemi
ATAli Takbiri-Borujeni
Ali Takbiri-Borujeni
STSam Takbiri
Sam Takbiri
AKArefeh Kazemi
Arefeh Kazemi

16 May 2022 in Energies
Verified
Journal Article
Open access
PDF file
Mohammad KazemiMohammad Kazemi
Mohammad Kazemi
AWAndrzej Wojtanowicz
Andrzej Wojtanowicz
The pressure bleed-down/build-up (B/B) testing is enforced by the Bureau of Safty and Environmental Enforcement (BSEE) regulations in the US for gas-leaking wells with recurrent casing head annular pressure dubbed “Sustained Casing Pressure” (SCP). The bleed down test involves bleeding the pressure with a needle valve. Once the pressure reached to zero or stabilized, the valve is closedand a 24-h pressure monitoring starts. Analysis of the tests mandated by regulations involves merely a qualitative assessment of the low or high level of environmental risk measured by leak size. A quantitative analysis—based on mathematical models—has been already proposed and used for sizing cement leaks but the models give ambiguous results due to oversimplifying assumptions of the cement leak system and disregard for the testing procedure. This work addresses shortcomings of the current B/B testing and analysis methods by approaching the testing procedure as a source of useful information about the system of annular well leakage. We demonstrate that using a mathematical model for globally matching all stages of the B/B test data would prioritize the pressure bleed-down stage over the buildup stage thus making the latter stage mostly irrelevant in providing information on the whole gas migration system. We verify the hypothesis that a stage-wise analysis would improve the results by separately considering three stages of the B/B test: pressure bleed down, constant flow (steady-state), and pressure buildup, and, then, comparatively reconciling values of the system parameters. The stage-by-stage approach is feasible because—as shown by the sensitivity analysis—each stage is controlled mostly by a single parameter. Also presented is the development of an improved procedure for performing the B-B test. The study shows that the operational parameters controlled by the test operator—duration and size of the needle valve opening, and pressure recording time step, might significantly change values of the test output—the minimum bleed down, and the maximum 24-h buildup pressures. It is also found that the zero bleed-down pressure does not necessarily indicate that the leak is small as it also depends upon the length and properties of the annular fluid column above the cement top.

16 October 2025 in Gases
Verified
Journal Article
Open access
PDF file
NSNadieh Salehi
Nadieh Salehi
Mohammad KazemiMohammad Kazemi
Mohammad Kazemi
MEMohammad Amin Esmaeilbeig
Mohammad Amin Esmaeilbeig
AHAbbas Helalizadeh
Abbas Helalizadeh
MMMehdi Bahari Moghaddam
Mehdi Bahari Moghaddam
Carbon dioxide (CO2), a major greenhouse gas, contributes significantly to global warming and environmental degradation. Carbon Capture, Utilization, and Storage (CCUS) is a promising strategy to mitigate atmospheric CO2 levels. One widely applied utilization approach involves injecting captured CO2 into depleted oil reservoirs to enhance oil recovery—a technique known as CO2-Enhanced Oil Recovery (CO2-EOR). The effectiveness of CO2-EOR largely depends on complex rock–fluid interactions, including mass transfer, wettability alteration, capillary pressure, and interfacial tension (IFT). Various factors, such as the presence of asphaltenes, salinity, pressure, temperature, and rock type, influence these interactions. This review explores the impact of these parameters on the IFT between CO2 and oil/water systems, drawing on findings from both experimental studies and molecular dynamics (MD) simulations. The literature indicates that increased temperature, reduced pressure, lower salinity, and the presence of asphaltenes tend to reduce IFT at the oil–water interface. Similarly, elevated temperature and pressure, along with asphaltene content, also lower the surface tension between CO2 and oil. Most MD simulations employ synthetic oil mixtures of various alkanes and use tools such as LAMMPS and GROMACS. Experimentally, the pendant drop method is most commonly used with crude oil and brine samples. Future research employing actual reservoir fluids and alternative measurement techniques may yield more accurate and representative IFT data, further advancing the application of CO2-EOR.