Polycrystalline graphene was transferred onto differently terminated epitaxial layers of boron-doped diamond deposited onto single crystal substrates. Chemical and electronic characterisation was performed using energy-filtered photoemission electron microscopy and angle-resolved photoemission spectroscopy. Electronic interaction between the diamond and graphene was observed, where doping of the graphene on the hydrogen and oxygen terminated diamond was n-doping of 250 meV and 0 meV respectively. We found that the wide window of achievable graphene doping is effectively determined by the diamond surface dipole, easily tuneable with a varying surface functionalisation. A Schottky junction using the graphene-diamond structure was clearly observed and shown to reduce downward band bending of the hydrogen terminated diamond, producing a Schottky barrier height of 330 meV.
13 November 2017 in Frontiers in Mechanical Engineering
Diamond-based thermionic emission devices could provide a means to produce clean and renewable energy through direct heat-to-electrical energy conversion. Hindering progress of the technology are the thermionic output current and threshold temperature of the emitter cathode. In this report, we study the effects on thermionic emission caused by in situ exposure of the diamond cathode to beta radiation. Nitrogen-doped diamond thin films were grown by microwave plasma chemical vapor deposition on molybdenum substrates. The hydrogen-terminated nanocrystalline diamond was studied using a vacuum diode setup with a 63Ni beta radiation source-embedded anode, which produced a 2.7-fold increase in emission current compared to a 59Ni-embedded control. The emission threshold temperature was also examined to further assess the enhancement of thermionic emission, with 63Ni lowering the threshold temperature by an average of 58 ± 11 °C compared to the 59Ni control. Various mechanisms for the enhancement are discussed, with a satisfactory explanation remaining elusive. Nevertheless, one possibility is discussed involving excitation of preexisting conduction band electrons that may skew their energy distribution toward higher energies.
The Large Plasma Device (LAPD) at UCLA (University of California, Los Angeles) produces an 18 m long, magnetized, quiescent, and uniform plasma at a high repetition rate to enable studies of fundamental plasma physics. Here, we report on a major upgrade to the LAPD plasma source that allows for more robust operation and significant expansion of achievable plasma parameters. The original plasma source made use of a heated barium oxide (BaO) coated nickel sheet as an electron emitter. This source had a number of drawbacks, including a limited range of plasma density (≲4.0 × 1012 cm−3), a limited discharge duration (∼10 ms), and susceptibility to poisoning following oxygen exposure. The new plasma source utilizes a 38 cm diameter lanthanum hexaboride (LaB6) cathode, which has a significantly higher emissivity, allowing for a much larger discharge power density, and is robust to exposure to air. Peak plasma density of up to 3.0 × 1013 cm−33 in helium gas has been achieved. The typical operating pressure is ∼10−5 Torr, while dynamic pressure can be achieved through the gas-puffing technique. Discharges as long as 70 ms have been produced, enabling a variety of long-time-scale studies of processes, such as turbulent particle transport. The new source has been in continuous operation for 14 months, having survived air leaks, power outages that led to rapid temperature changes on the cathode and heater, and planned machine openings. We describe the design, construction, and initial operation of this novel new large-area LaB6 plasma source.
Material band structures of occupied electronic states are obtainable using conventional angle‐resolved photoemission experiments, leaving the unoccupied states far less explored. Here, an alternative approach is built on and expanded to investigate thermalized photoelectrons emitted from crystal surfaces. A model for electron emission is constructed and reveals the material unoccupied state band structure. Potentially applicable to any material and independent from the secondary electron generation mechanism, it is demonstrated on diamond and copper using different light sources. Moreover, the diamond indirect band gap is directly observed and the transverse effective mass at the conduction band minimum can be experimentally obtained, mt = (0.21 ± 0.015) me. This offers a convenient path for angle‐resolved photoemission data interpretation and empty‐state information extraction.
Electrodeposition of Pb on Au has been of interest for the variety of surface phenomena such as the UnderPotential Deposition (UPD) and surface alloying. Here, we examined the interface between the electrodeposited Pb film on Au, using surface sensitive techniques such as X-ray Photoelectron Spectroscopy (XPS), Ultraviolet Photoelectron Spectroscopy (UPS), Energy-Filtered Photoemission Electron Microscopy (EF-PEEM) and Work Function (WF) mapping. The initially electrodeposited Pb overlayer (~4 ML equivalent thickness) was transferred from the electrochemical cell to the UHV system. The deposited Pb layer was subjected to Argon sputtering cycles to remove oxide formed due to air exposure and gradually thinned down to a monolayer level. Surface science acquisitions showed the existence of a mixed oxide/metallic Pb overlayer at the monolayer level that transformed to a metallic Pb upon high temperature annealing (380 °C for 1 h) and measured changes of the electronic interaction that can be explained by Pb/Au surface alloy formation. The results show the electronic interaction between metallic Pb and Au is different from the interaction of Au with the PbO and Pb/PbO mixed layer; the oxide interface is less strained so the surface stress driven mixing between Au is not favored. The work illustrates applications of highly surface sensitive methods in the characterization of the surface alloy systems that can be extended to other complex and ultrathin mixed-metallic systems (designed or spontaneously formed).