Plastics have recently become an indispensable part of everyone’s daily life due to their versatility, durability, light weight, and low production costs. The increasing production and use of plastics poses great environmental problems due to their incomplete utilization, a very long period of biodegradation, and a negative impact on living organisms. Decomposing plastics lead to the formation of microplastics, which accumulate in the environment and living organisms, becoming part of the food chain. The contamination of soils and water with poly(vinyl chloride) (PVC) seriously threatens ecosystems around the world. Their durability and low weight make microplastic particles easily transported through water or air, ending up in the soil. Thus, the problem of microplastic pollution affects the entire ecosystem. Since microplastics are commonly found in both drinking and bottled water, humans are also exposed to their harmful effects. Because of existing risks associated with the PVC microplastic contamination of the ecosystem, intensive research is underway to develop methods to clean and remove it from the environment. The pollution of the environment with plastic, and especially microplastic, results in the reduction of both water and soil resources used for agricultural and utility purposes. This review provides an overview of PVC’s environmental impact and its disposal options.

This review presents a comprehensive account of methods which are commonly applied for the synthesis of α- aminophosphonic acids. In the following order, protocols based on the methodologies listed below are discussed: a) simultaneous formation of P-CN systems; b) nucleophilic substitution with phosphoroorganic nucleophiles; c) additions of the P-H functions to multiple C-N bonds; d) α – amination of phosphonates and functionalized alkylphosphonates; e) modifications of the side chain of aminoalkylphosphonates; f) modifications of phosphorus functions and h) modifications of functions containing nitrogen.

The paper presents the new eco-friendly method of bleaching process of the cellulose fibre materials. Cellulose materials were bleached using hydrogen peroxide (both in aqueous solution, vapours, ozone and by the combined action of gaseous hydrogen peroxide and ozone. The method using hydrogen peroxide in aqueous solution presents the standard procedure and was used as the comparison technique. The bleaching processes using gaseous oxidants were carried out in a prototype device for dry, low-temperature treatment of fibrous materials with the use of oxidising agents in the gas phase. The influence of the innovative gas-phase bleaching method on the cotton samples’ properties was analysed by Scanning Electron Microscopy (SEM), evaluation of the colour and whiteness, assessment of the polymerisation degree (DP), analysis of the mechanical properties and sorption capacity as well as microbiological assessment against colonies of Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria. The comparison of the obtained results led to the conclusion that the bleaching processes using gas-phase agents—vaporised hydrogen peroxide, ozone or their combination—are non-invasive. The applied bleaching processes resulted in a slightly lower whiteness parameters than standard bath bleaching. After the bleaching processes with ozone and vaporised hydrogen peroxide separately, the decrease in the DP and tensile strength was similar to that observed after the bleaching with aqueous H₂O₂. When both processes were used together, a higher reduction in DP and tensile strength was noticed. Both oxidising agents showed a strong biocidal effect against bacteria. Gas-phase bleaching procedures, due to the lower temperature (35 °C vs. 98 °C) and minimal water consumption, have economic and environmental advantages, which allows their use in semi-industrial applications. It has been shown that the treatment of cotton fabrics using ozone and hydrogen peroxide in the gas phase allows to simultaneously obtain the bleaching and disinfection effect.

The influence of various factors on the removal efficiency of selected pharmaceuticals by membrane filtration was investigated. Several commercial polymer membranes were used for nanofiltration (NF) from various manufacturers. The studies were conducted for ibuprofen (IBF), amoxicillin (AMX), diclofenac (DCF), tetracycline (TRC), salicylic acid (SA) and acetylsalicylic acid (ASA). The influence of the structure and properties of the tested compounds on the retention coefficient and filtration rate was investigated. The influence of pH on the filtration parameters was also checked. The properties of selected membranes influencing the retention of pharmaceuticals and filtrate flux were analysed. An extensive analysis of the retention coefficients dependence on the contact angle and surface free energy was performed. It was found that there is a correlation between the hydrophilicity of the membrane and the effectiveness and efficiency of the membrane. As the contact angle of membrane increased, the flow rate of the filtrate stream increased, while the retention coefficient decreased. The studies showed that the best separation efficiency was achieved for compounds with a molecular weight (MW) greater than 300 g/mol. During the filtration of pharmaceuticals with MW ranging from 300 to 450 g/mol, the type of membrane used practically did not affect the filtration efficiency and a high degree of retention was achieved. In the case of low MW molecules (SA and ASA), a significant decrease in the separation efficiency during the process was noted.

Skin regeneration requires a three-dimensional (3D) scaffold for cell adhesion, growth and proliferation. A type of the scaffold offering a 3D structure is a nonwoven material produced via a melt-blown technique. Process parameters of this technique can be adapted to improve the cellular response. Polylactic acid (PLA) was used to produce a nonwoven scaffold by a melt-blown technique. The key process parameters, i.e., the head and air temperature, were changed in the range from 180–270 °C to obtain eight different materials (MB1–MB8). The relationships between the process parameters, morphology, porosity, thermal properties and the cellular response were explored in this study. The mean fiber diameters ranged from 3 to 120 µm. The average material roughness values were between 47 and 160 µm, whereas the pore diameters ranged from 5 to 400 µm. The calorimetry thermograms revealed a correlation between the temperature parameters and crystallization. The response of keratinocytes and macrophages exhibited a higher cell viability on thicker fibers. The cell-scaffold interaction was observed via SEM after 7 days. This result proved that the features of melt-blown nonwoven scaffolds depended on the processing parameters, such as head temperature and air temperature. Thanks to examinations, the most suitable scaffolds for skin tissue regeneration were selected.

The paper presents the method of synthesis; physico-technical and biological characterization of a new composite material (PLA–Cu⁰) obtained by sputter deposition of copper on melt-blown poly(lactide) (PLA) non-woven fabrics. The analysis of these biofunctionalized non-woven fabrics included: ultraviolet/visible (UV/VIS) transmittance; scanning electron microscopy/energy-dispersive spectroscopy (SEM/EDS); attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy; ability to block UV radiation; filtration parameters (air permeability); and tensile testing. The functionalized non-woven composite materials were subjected to antimicrobial tests against colonies of Gram-negative (Escherichia coli), Gram-positive (Staphylococcus aureus) bacteria and antifungal tests against the Chaetomium globosum fungal mould species. The antibacterial and antifungal activity of PLA–Cu⁰ suggests potential applications as an antimicrobial material.