Tissue engineering applications commonly encompass the use of three-dimensional (3D) scaffolds to provide a suitable microenvironment for the incorporation of cells or growth factors to regenerate damaged tissues or organs. These scaffolds serve to mimic the actual in vivo microenvironment where cells interact and behave according to the mechanical cues obtained from the surrounding 3D environment. Hence, the material properties of the scaffolds are vital in determining cellular response and fate. These 3D scaffolds are generally highly porous with interconnected pore networks to facilitate nutrient and oxygen diffusion and waste removal. This review focuses on the various fabrication techniques (e.g., conventional and rapid prototyping methods) that have been employed to fabricate 3D scaffolds of different pore sizes and porosity. The different pore size and porosity measurement methods will also be discussed. Scaffolds with graded porosity have also been studied for their ability to better represent the actual in vivo situation where cells are exposed to layers of different tissues with varying properties. In addition, the ability of pore size and porosity of scaffolds to direct cellular responses and alter the mechanical properties of scaffolds will be reviewed, followed by a look at nature's own scaffold, the extracellular matrix. Overall, the limitations of current scaffold fabrication approaches for tissue engineering applications and some novel and promising alternatives will be highlighted.
The incorporation and presentation of cell recognition ligands on the surfaces of biodegradable blood-vessel implants to promote endothelialisation is considered to be a promising approach to prevent platelet aggregation and hence thrombogenesis. In this study, cell-adhesive collagen was covalently immobilised onto polycaprolactone (PCL) substrates via surface-initiated atom transfer radical polymerization (ATRP) to improve cell–material interactions. Functional polymer brushes of poly(methacrylic acid) (P(MAA)) containing dense and reactive carboxyl groups (–COOH) were formed on the PCL substrates in a controllable manner. The amount of collagen, which was conjugated to the pendant carboxyl groups via carbodiimide chemistry, increased with the concentration of –COOH groups on the grafted P(MAA) brushes. The affinity and growth of endothelial cells (ECs) were found to be significantly improved on the collagen-immobilised PCL substrates, and this improvement is positively correlated with the amount of covalently conjugated collagen. Thus, surface-initiated ATRP provides an alternative methodology for the surface functionalisation of biodegradable polyester scaffolds to enable the formation of a confluent layer of ECs. An optimally endothelialised material surface will play a major role in the minimisation of thrombogenicity and inflammation, and hence can be potentially used for vascular graft applications.
To enhance the cytocompatibility of polyvinylidene fluoride (PVDF) films, arginine–glycine–aspartic acid (RGD) peptide-click-poly(glycidyl methacrylate) (PGMA) polymer brushes were grafted onto the PVDF surface by the combination of surface-initiated atom transfer radical polymerization (ATRP) and click reaction. The direct initiation of the secondary fluorine atoms of PVDF backbone allowed for grafting of the PGMA brushes containing reactive epoxy groups. Subsequent introduction of the azide groups onto the side chain of PGMA brushes was achieved by the ring-open reaction of the epoxy groups with sodium azide. The cell adhesive RGD peptide was finally conjugated onto the PGMA brushes via alkyne-azide click reaction. Kinetic studies revealed that the PGMA chain growth from the PVDF surface was consistent with a “controlled” process, and that the amount of immobilized RGD peptide on the PGMA brushes increased with the concentration of the pendant azide groups. The specificity of cellular interactions of adipose tissue-derived stem cells (ASCs) on the functionalized PVDF films was investigated. Results demonstrated that cell adhesion and proliferation of ASCs were significantly improved on the RGD-immobilized PVDF substrates, and this improvement was positively correlated with the surface concentration of covalently-bonded RGD peptide. With the inherent superior chemical and mechanical properties of PVDF films and the biocompatible nature of cell-adhesive peptides, surface functionalized PVDF films are potentially useful for biomedical and tissue engineering applications.
1 June 2013 in Colloids and Surfaces B: Biointerfaces
This study describes the preparation and characterization of a biodegradable 3D hydrogel constructed from hydroxypropyl cellulose (HPC), modified with bifunctional methacrylic anhydride (MA) to form hydroxypropyl cellulose methacrylate (HPC-MA), for adipose tissue engineering applications. The hydrogels were prepared from three different concentrations (10 wt%, 15 wt% and 20 wt%) of HPC-MA with 0.35 degree of substitution. HPC-MA hydrogel scaffolds with open biphasic features were prepared by exploiting the thermal responsive phase behavior of HPC and temperature mediated phase separation of HPC-MA. The resulting scaffolds exhibited pore sizes ranging from 30 to 300 μm and an interconnected porosity of ∼90%. The swelling ratio (SR) and storage modulus of HPC-MA scaffolds were in the range of 12.94 to 35.83 and 0.75 to 4.28 kPa, respectively. The swelling ratio and storage modulus suggested that the scaffold exhibits high water retention, allowing medium exchange during cell culturing and that it is suitable for adipose tissue regeneration. The HPC-MA scaffolds were found to be biocompatible to human adipose-derived stem cells (ASCs). ASCs were successfully differentiated into the adipocytes inside the scaffolds, and therefore demonstrated the potential application of these HPC-MA scaffolds for adipose tissue engineering.