Chunli Zhou

Mr. Chunli Zhou

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 May 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
CZChunli Zhou
Chunli Zhou
WCWei Chen
Wei Chen
XRXiaolong Ruan
Xiaolong Ruan
XTXueying Tang
Xueying Tang
In order to study the axial compression behavior of concrete-filled steel tubular (CFST) columns filled with high titanium slag, a total of 32 specimens, including normal CFST columns, half-high titanium slag CFST columns, and full-high titanium slag CFST columns, were used as experimental samples in this study. The axial compression behaviors of high titanium slag CFST columns and normal CFST columns with various parameters such as length–diameter ratio, strength grade of concrete, strength grade of steel tube, steel content ratio, etc., were evaluated and compared through axial compression testing under monotonic static loading. The results showed that the axial compressive behaviors of high titanium slag CFST columns with various length–diameter ratios were not significantly different from those of normal CFST columns, both of which showed good axial compression performance. In addition, the length–diameter ratio limit between short and medium long column was from 3.5 to 4.4. The length–diameter ratio was the main factor influencing the shape of load–deformation curve of CFST columns. The casing hoop coefficient also had a great influence on the bearing capacity of short columns, while the influence on that of middle and long columns was not obvious. In the end, the bearing capacities of all specimens were calculated by bearing capacity formulas in European EC4, American AISC360-10, and Chinese GB50936-2014 standards. The calculated values were in good agreement with the test results.

1 January 2019 in Advances in Civil Engineering
Verified
Journal Article
Open access
CZChunli Zhou
Chunli Zhou
XLXiaowei Li
Xiaowei Li
DWDongbo Wang
Dongbo Wang
SXshunxiang xia
shunxiang xia
Based on a practical project, the construction method of circular reinforced concrete (RC) columns strengthened with externally wrapped steel plates was introduced in this paper. In order to study the bearing capacity and seismic performance of circular RC columns after strengthening, a formula for calculating the bearing capacity of circular RC columns strengthened with externally wrapped steel plates was derived, with reference to the Code for Design of Strengthening Concrete Structure. Through ABAQUS software, the vertical monotone static loading analysis and the horizontal low‐cyclic reversed loading analysis were carried out, respectively, before and after the strengthening of the full‐size RC columns in this project. The results showed that the bearing capacity of the normal section of the RC column after strengthening was about 80% higher than that before strengthening, and the results of FEM software were in accord with the calculation results of theoretical formula to some degree. Under horizontal low‐cyclic reversed loading, the columns after strengthening had both plumper hysteresis curves and higher ductility factors and equivalent viscous damping coefficient than those before strengthening, indicating the energy dissipation capacity, plastic deformation capacity, and seismic performance of the RC columns after strengthening were all obviously improved.

1 January 2019 in Advances in Civil Engineering
Verified
Journal Article
Open access
CZChunli Zhou
Chunli Zhou
JSJinkun Sun
Jinkun Sun
ZZZhaorong Zeng
Zhaorong Zeng
JLJie Liu
Jie Liu
Based on practical frame structures, constructional methods of the reinforced concrete (RC) frame beam strengthened by using an exterior‐wrapping U‐shaped steel plate are introduced. With reference to the code for design of strengthening concrete structure, the bearing capacity formula of the RC frame beams strengthened by using the exterior‐wrapping U‐shaped steel plate is briefly derived. After that, the finite element analysis of the frame beam before and after the reinforcement of the engineering example is carried out through ABAQUS software, and the results of the analysis of the bearing capacity are compared with the calculation results of the theoretical formula. At the same time, through comparing and analysing the U‐shaped steel plate strengthening method and the “angle steel + batten plate” strengthening method, the result that the RC beam strengthened by using the exterior‐wrapping U‐shaped steel plate has better mechanical performance is drawn. Finally, the application of the exterior‐wrapping U‐shaped steel plate strengthening method is rationally suggested.