In recent years, people’s environmental awareness has increased. The high density of the urban population has caused a considerable increase in the demand for car washing services, which has created large quantities of car wash wastewater. The main pollutants in car wash wastewater are detergents, dirt, oil, and grease. Untreated wastewater released into rainwater sewer systems or other water bodies may pollute the water and generate excessive bubble foams, which negatively affects urban appearance. Car washes are divided into mechanical car washes and manual or self-service car washes. In general, car washes have a small operation and scale, occupy limited land, and cannot afford wastewater treatment costs. Therefore, most car washes are not equipped with wastewater treatment facilities. Consequently, the discharge of wastewater from car washes negatively affects the water quality in the surrounding environment and results in wasteful use of water resources. This study reviewed 68 research papers on the quality, treatment techniques, treatment costs, and treatment effectiveness of car wash wastewater to provide a reference for car wash operators to contribute to the preservation of water resources. We found that there is a higher chance of recycling car wash wastewater when combing two different techniques for car wash wastewater treatment.
Hydrocyclone separation techniques have recently been used in an increasing number of applications. Three-dimensional simulation of a hydrocyclone was accomplished under three different flow splits S, say, 0.14, 0.25, and 0.44. Supplementary to standard Reynolds stress turbulence model (RSM), hydrodynamic behavior of flow in the hydrocyclone could be realized more clearly. With a discrete-phase model (DPM), particles in the hydrocyclone could be traced and the performance of the hydrocyclone could be evaluated. This simulation showed that the position or shape of a vortex finder might be a factor influencing short circuit. Particles with large densities have long residence times at small size, while particles with small densities have long residence times at large size. A hot zone that particles flow into will eventually flow out through overflow is three-dimensionally displayed.
With the increase in transportation demand and facilities in this era and the significant improvement in people’s living standards, the annual production and sales of vehicles are steadily increasing. With this, the issues of car wash wastewater treatment and water pollution are becoming more and more serious. Car wash wastewater mainly comprises fine sand, slick oil, suspended solids (SS), and surfactants, and can be quantified as chemical oxygen demand (COD) on a normative basis. This study examines the use of cyclo-flow filtration with high filtrate flux to treat car wash wastewater to solve issue of limited space in metropolitan areas and increase the willingness of the industry to invest in car wash equipment to recover water resources. The average removal rates of SS and COD are about 81% and 43%, respectively. Compared with current technology, the price of recycled water can compensate for operating costs, requiring minimal operating space owing to the single-unit cyclo-flow filtration system.
In this study, through simulation and experimental verification, we proposed a novel hydrocyclone in which a tubular ceramic membrane passed through the overflow outlet to the underflow outlet. The centers of overflow and underflow outlets were tubular membranes equipped with an exit of outside-in filtration, and the overflow the underflow outlets were shaped into annular (donut shape) exits. Thus, this novel hydrocyclone has three outlets, namely the overflow dilute liquid, the underflow concentrated liquid, and clear filtrate. This system enabled higher dilution of hydrocyclone overflow concentration than that in the traditional system. Furthermore, underflow was more concentrated, and we obtained a clear filtrate. Therefore, this device can simultaneously perform classification and filtration, which is valuable for special liquid recycling. For instance, in wafer cutting fluid recovery in solar energy processes, the fluid with more silicon can function as the overflow, the fluid with more silicon carbide can function as the underflow, and the polyethylene glycol (PEG) organic solvent can function as the clear filtrate.
In the proposed centrifugal filtration device, a filter is mounted in the center of the centrifugal chamber. The particles move towards the centrifuge wall away from the filter under centrifugal force, so a filtration cake is unlikely to accumulate here. The working fluid is injected continuously, so the feed pressure is higher than the discharge pressure, which compels the light-phase fluid to leave through the filter as filtrate. The filtrate flux rate and the movement of particles in the centrifugal chamber of the proposed filtration device were investigated using different powder particle sizes, concentrations of working fluid, centrifugal chamber rotation speeds, and filters. With a higher centrifugal chamber rotation speed, the centrifugal force acting on the particles in the centrifugal chamber was stronger, and the particles were less likely to adhere to the central filter; hence, a larger amount of filtrate was produced.
1 August 2019 in Journal of the Taiwan Institute of Chemical Engineers