Gradation segregation strongly affects the service performance of asphalt pavement. However, rare studies focus on the influences of segregation on asphalt mixture as it is difficult to simulate segregation in a laboratory. This paper presents a research aiming to evaluate the effects of gradation segregation using the two dimensional (2D) discrete element method (DEM). To achieve this objective, the gradation segregation levels are defined according to the differences between control and segregated gradations. Based on this, asphalt mixtures with three gradations at three segregation levels were selected. The corresponding 2D DEM models were then built using Particle Flow Code 2D (PFC 2D). The aggregate skeletons in the asphalt mixture were determined separately by means of the contact point and contact force. Based on this, the variations on the aggregate skeleton, aggregate distribution, and mechanical properties of the asphalt mixture under vertical load were studied at three different segregation levels. This study indicates that the aggregate skeleton in asphalt mixture can be affected by the gradation segregation. The correlation between gradation segregation and mechanical property is also determined in this study.

This study considered the effect of pavement aggregate grain size on tyre–pavement contact interaction during the late stages of pavement skid resistance. First, hemispherical shells 7, 9, and 13 mm in diameter were used to simulate coarse pavement aggregates. Subsequently, a three-dimensional finite element tyre–pavement contact model developed using ABAQUS was employed to analyse the contact interaction between each simplified pavement type and the tyre under steady–state rolling and braking conditions. Finally, the concept of occlusal depth was proposed and applied to characterise pavement skid resistance. The results showed that under steady–state rolling conditions, the peak contact stress of the simplified pavement increased with the pavement mean texture depth, whereas the contact area decreased. Under steady–state braking conditions, the effect of the contact interaction between the tyre and simplified pavement aggregates was ranked in order of superiority as aggregate grain sizes of 9, 7, and 13 mm, indicating that aggregate grain size did not exhibit any correlation with tyre–pavement contact interaction. Additionally, the squares of linear correlation coefficients between the pavement cumulative occlusal depth and horizontal braking force reached 0.921, 0.941, 0.889, and 0.894 for vehicle speeds of 30, 60, 90, and 120 km/h, respectively, indicating that they could be used to assess pavement skid resistance.

To eliminate the effects of image’s light and shade difference when separating and distinguishing the material composition, a method is put forward, namely, ring‐type and partitions threshold segmentation. It means setting up different segment threshold for different areas of the same image and then combining these different areas into one image. Furthermore, by analyzing the CT image before and after the RLWT rutting test for the drilling specimen and Marshall specimen and taking the volume of air voids and the angle (alpha) between max main axis and X axis, the differences of two kinds of specimens’ macrotest results were discussed from internal structure distribution. Here, we show that there are differences between macrotest results of two kinds of specimens because of internal air voids and aggregate distribution, which should be considered for compliance testing.

To investigate the influence of pavement texture on tire hydroplaning, this study utilized laser scanning to capture the surface characteristics of three asphalt mixtures—AC-13, SMA-13, and OGFC-13—across fifteen rutting plate specimens. Three-dimensional (3D) pavement models were reconstructed to incorporate realistic texture data. Finite element simulations, employing fluid-structure interaction and explicit dynamics in Abaqus, were conducted to model tire-water-pavement interactions. The results indicate that the anti-skid performance ranks as OGFC > SMA > AC. However, despite OGFC and SMA exhibiting comparable anti-skid metrics (e.g., pendulum friction value and mean texture depth), OGFC’s superior texture uniformity results in significantly better hydroplaning resistance. Additionally, tire tread depth critically influences hydroplaning speed. A novel Anti-Slip Comprehensive Texture Index (ACTI) was proposed to evaluate pavement texture uniformity, providing a more comprehensive assessment of anti-skid performance. These findings underscore the importance of texture uniformity in enhancing pavement safety under wet conditions.

The degradation of styrene-butadiene-styrene (SBS) modified asphalt under thermal-oxidative aging can reduce pavement service life. Lignin is a renewable material with active phenolic hydroxyl groups. Incorporating lignin into SBS modified asphalt may provide a potential bio-based auxiliary modification route. To investigate the antioxidative effect and rheological properties of SBS modified asphalt after adding lignin, a molecular dynamics test and experimental tests were employed. The molecular simulation results suggested that lignin preferentially associated with asphaltene and resin molecules and changed the molecular mobility of asphalt components in a component-dependent manner. The SBS/lignin composite modified asphalt was evaluated by temperature sweep (TS), Multiple Stress Creep and Recovery (MSCR), Linear Amplitude Sweep (LAS) and Fourier transform infrared spectroscopy (FTIR). Rheological tests showed that lignin increased the complex shear modulus and rutting factor. LAS results showed that lignin reduced the fatigue life of SBS-modified asphalt in the unaged state due to increased stiffness and embrittlement. However, after long-term aging, the lignin-containing binders retained higher fatigue resistance than the SBS-only control, which may be related to the slower evolution of oxidation-related functional groups and SBS-related spectral indices. FTIR analysis provided semi-quantitative evidence that lignin addition reduced the growth of sulfoxide-related bands and helped maintain the polybutadiene-related index during aging. Overall, lignin may serve as a potential auxiliary antioxidant modifier for SBS modified asphalt, while its exact source-specific molecular mechanism requires further verification.

In order to better understand the evolution of the road-surface macro-texture, kneading test was conducted by using a kneading machine. The kneading machine was invented by improving a national standard rutting machine. Ten specimens were studied, which have different values in various factors (kneading temperature, aggregate gradation and aggregate type). Macrotexture measurements were carried out at different kneading times (0, 2, 4, 6, and 8 h). The macro-texture profiles were measured by means of the Laser-measuring Technique, showing on an area of 10 × 10 cm. Two indicators, the Peak Angle and the Kneading Loss, were adopted to describe and quantify the evolution of the macro-texture. The results showed that aggregate gradation, kneading time and kneading temperature can significantly impact the skid resistance performance of asphalt pavements; Kneading will affect the distribution of Peak Angles and increase the Kneading Loss.