The performance of flywheel motor is decided by the airgap flux density waveform. This paper establishes an efficient model to optimize the airgap flux density waveform and provides the Pareto optimal solutions, which give the design boundary of airgap flux density waveform for flywheel motor. The key elements of the structure of permanent magnet and the airgap are considered to optimize the sinusoidal distortion rate and the fundamental amplitude of the airgap flux density waveform. The brief optimization process is three steps: (1) sampling by maximum projection design; (2) building surrogate model by the Kriging method; and (3) multi-objective optimization by non-dominated sorting genetic algorithm with elitism approach (NSGA-2) based on the Kriging model. Then, the Pareto optimal solutions are obtained. The three cases optimized by different strategies are compared, and the optimization method is verified by finite-element method.
This paper presents an efficient three-dimensional (3D) structural model for bump-type gas foil bearings (GFBs) developed by considering friction. The foil structures are modeled with a 3D shell finite element model. Using the bump foil mechanical characteristics, the Guyan reduction and component mode synthesis methods are adopted to improve computational efficiency while guaranteeing accurate static responses. A contact model that includes friction and separation behaviors is presented to model the interactions of the bump foil with the top foil and bearing sleeve. The proposed structural model was validated with published analytical and experimental results. The coupled elastohydrodynamics model of GFBs was established by integration of the proposed structural model with data on hydrodynamic films, and it was validated by comparisons with existing experimental results. The performance of a bearing with an angular misalignment was studied numerically, revealing that the reaction torques of the misaligned bearing predicted by GFB models with 2D and 3D foil structure models are quite different. The 3D foil structure model should be used to study GFB misalignment.
This paper proposes an efficient and accurate surrogate model, called adaptive Kriging model based on maximum projection (MaxPro) design (AKMMP), and establishes the design method by using the non-dominated sorting genetic algorithm with the elitism approach (NSGA-2) and AKMMP to optimize the mass and torque density as the performance parameters of flywheel motor with consideration of rotational inertia. The Pareto optimal solution set of flywheel motor is provided and used as the design border for the flywheel motor. The detailed design parameters are the armature diameter and axial length, rotor and stator split ratios, and permanent magnet width related to the mass and torque density. The brief optimization process includes five steps: A) getting the initial samples by MaxPro design; B) building the Kriging model based on the initial samples; C) optimization by NSGA-2 based on the Kriging model; D) selecting the corrected test point by the proposed sample strategy; and E) judging the convergence. The seven cases with different masses are analyzed, and the finite-element method is used to verify the optimization method.
The lack of endurance is an important reason restricting further development of unmanned aerial vehicles (UAVs). Accurately estimating the state of charge (SOC) of the Li-Po battery can maximize the battery energy utilization and improve the endurance of UAVs. In this paper, the main current methods for estimating the SOC of vehicles were explored and discussed to unveil their advantages and disadvantages. In addition, the extended Kalman filter algorithm based on an equivalent circuit model was used to estimate SOC of power-type Li-Po batteries at different temperatures. The result showed that the closed-loop control method can effectively improve the battery life of small-sized electric UAVs.
The flame combustion processes involves chemical reactions and therefore flame stability is difficult to accurately assess. Based on flame radiation measuring parameters, a new synthetic evaluation system of flame combustion stability is established. A series of combustion conditions with various fuel/air ratios is investigated. Flame radiation luminance fluctuating information is acquired on a low-cost flame detection device. Power spectrum and bi-spectral information of the phase domain are derived from time domain signals based on Fourier transform and higher order statistics based upon a de-noising algorithm. The time–frequency characteristics and the features of the bi-spectrum under various combustion conditions are qualitatively analyzed, and the simultaneous descriptive parameters from time, frequency, and phase domain are extracted. A theoretical model for comprehensive fuzzy evaluation has been constructed, and also an index system has been established. It is demonstrated that this judgment system is reasonable and effective. The results can be used as an analyzing tool for process engineers for improving combustion conditions.
Flywheel motor topology was analyzed, and a main performance optimization model and stator/rotor core loss optimization model were provided. Then, an adaptive Kriging Surrogate model based on the MaxPro design (AKMMP) was used, improving the optimization precision and efficiency. Based on these preliminary outcomes, a stepwise optimization design method of flywheel motor based on AKMMP was proposed. The brief design process includes five steps: 1) initial structure of the flywheel motor: outer rotor, 16 poles/18 slots, double layer concentrated winding, inclined shoulder flat bottom slot, water cooling and F grade insulation. 2) First step optimization: performance optimization using AKMMP to obtain the performance Pareto solution set. 3) According to the performance of a flywheel motor, selection of the suitable case from the performance Pareto solution set. 4) Second step optimization: further optimization of the stator/rotor core loss for the case obtained before using AKMMP. 5) Creation of the final optimization design structure. Then complete the flywheel motor design by the stepwise optimization design method. Finally, the prototype of the flywheel motor was produced, and performance testing was performed.