The natural radioactive decay of uranium in rocks and soils gives rise to the presence of radon in groundwater. The existence of radon in groundwater at activity levels way higher than the reference limits set by US-EPA and WHO was widely covered in literature. The exposure to elevated levels of radon in ground and drinking water have been reported in literature to cause adverse health impacts. The aim of the present paper is to give an overview of radon gas in groundwater followed by the safe limits suggested by international organizations and agencies such as US-EPA and WHO. The paper also discusses the health effects associated with the exposure to radon levels and the estimation of the annual effective dose through ingestion and inhalation. This is followed by the radon levels around the world as well as the corresponding annual effective doses reported in literature. The determination techniques of radon levels in water covered in literature such as liquid scintillation counting, gamma-ray spectrometry and emanometry were also discussed and reviewed in the present work. Next, the paper sheds light on the most frequently used treatment techniques such as aeration, adsorption, filtration as well as biological techniques and evaluates their efficiency in mitigating radon levels in water. The paper also highlights the main precautions and future mitigation plans for radon in groundwater as well as delved onto future research perspectives of radon. It was found out that the type of rock played a key role in determining the radon levels. For instance, granitic rock types were reported to contribute to the elevation in the groundwater radon levels due to their characteristic permeability as a result of the formed fractures as well as their natural incorporation of high levels of uranium. Some of the reported radon levels in groundwater in literature were way higher than the guidelines set by the World Health Organization (WHO) for drinking water and US-EPA alternative higher maximum contaminant level. This review paper could be of importance to researchers working on the evaluation as well as the treatment of radon gas in water as it will provide a critical and state of the art review on radon gas in groundwater.

A novel biochar (BC) from Acaciatortilis trees pruning waste was synthesized and tested for the removal of phosphate from aqueous solutions. The BC was prepared by calcination at 600 °C and doped with Fe₃O₄ and MgO by hydrothermal process. The presence of iron and magnesium ions in the modified BC was confirmed by EDS analysis and X-ray diffraction (XRD) methods. Both unmodified and doped BCs were tested for phosphate removal from synthetic 1–500 ppm aqueous solutions. While the unmodified BC did not show any significant removal of phosphate from aqueous solutions, the modified BC almost completely removed phosphate from water. The enhancement in removal efficiency is due to an increase in the overall surface charge and surface area of BC as a result of doping with Fe₃O₄ and MgO salts. The average porosity and BET surface area corresponding to the plain BC increased by more than 20% from 322 to 394 m²/g after modification by impregnation with iron oxide and magnesium oxide. The modificaiton of BC with Fe₃O₄ and MgO nanoparticles was observed to increase the point of zero electric charge (PZC) from pH 3.4 (corresponding to plain BC) to pH 5.3 (corresponding to modified BC). The adsorption process was very fast and a phosphate removal value of 82.5% was reached only after 30 min of adsorption, while the removal efficiency after 4 h of adsorption was 97.5%. The rapid removal efficiency in short contact time is attributed to the high surface area of BC and strong bonding between the modified BC surface and PO₄³⁻ ions. The highest adsorption capacity was observed to correspond to 98.5 mg/g which was achieved at PO₄³⁻ concentration of 500 ppm and pH 8.5. Moreover, after fitting the adsorption data onto four of the most widely used adsorption isotherm models, the adsorption of PO₄³⁻ onto BC can be better described by the Langmuir isotherm model.

In this work, novel polysulphone (PS) porous membranes for water desalination, incorporated with commercial and produced carbon nanotubes (CNT), were fabricated and analyzed. It was demonstrated that changing the main characteristics of CNT (e.g., loading in the dope solutions, aspect ratio, and functionality) significantly affected the membrane properties and performance including porosity, water flux, and mechanical and surface properties. The water flux of the fabricated membranes increased considerably (up to 20 times) along with the increase in CNT loading. Conversely, yield stress and Young’s modulus of the membranes dropped with the increase in the CNT loading mainly due to porosity increase. It was shown that the elongation at fracture for PS/0.25 wt. % CNT membrane was much higher than for pristine PS membrane due to enhanced compatibility of commercial CNTs with PS matrix. More pronounced effect on membrane’s mechanical properties was observed due to compatibility of CNTs with PS matrix when compared to other factors (i.e., changes in the CNT aspect ratio). The water contact angle for PS membranes incorporated with commercial CNT sharply decreased from 73° to 53° (membrane hydrophilization) for membranes with 0.1 and 1.0 wt. % of CNTs, while for the same loading of produced CNTs the water contact angles for the membrane samples increased from 66° to 72°. The obtained results show that complex interplay of various factors such as: loading of CNT in the dope solutions, aspect ratio, and functionality of CNT. These features can be used to engineer membranes with desired properties and performance.