The use of distributed energy resources is increasingly being pursued as a supplement and an alternative to large conventional central power stations. The specification of a power-electronic interface is subject to requirements related not only to the renewable energy source itself but also to its effects on the power-system operation, especially where the intermittent energy source constitutes a significant part of the total system capacity. In this paper, new trends in power electronics for the integration of wind and photovoltaic (PV) power generators are presented. A review of the appropriate storage-system technology used for the integration of intermittent renewable energy sources is also introduced. Discussions about common and future trends in renewable energy systems based on reliability and maturity of each technology are presented

Energy storage systems (ESSs) are enabling technologies for well-established and new applications such as power peak shaving, electric vehicles, integration of renewable energies, etc. This paper presents a review of ESSs for transport and grid applications, covering several aspects as the storage technology, the main applications, and the power converters used to operate some of the energy storage technologies. Special attention is given to the different applications, providing a deep description of the system and addressing the most suitable storage technology. The main objective of this paper is to introduce the subject and to give an updated reference to nonspecialist, academic, and engineers in the field of power electronics.

In the last few years, restrictive grid codes have arisen to ensure the performance and stability of electrical networks, which experience a massive integration of renewable energy sources and distributed generation systems that are normally connected to the grid through electronic power converters. In these codes, the injection of positive- and negative-sequence current components becomes necessary for fulfilling, among others, the low-voltage ride-through requirements during balanced and unbalanced grid faults. However, the performance of classical dq current controllers, applied to power converters, under unbalanced grid-voltage conditions is highly deficient, due to the unavoidable appearance of current oscillations. This paper analyzes the performance of the double synchronous reference frame controller and improves its structure by adding a decoupling network for estimating and compensating the undesirable current oscillations. Experimental results will demonstrate the validity of the proposed decoupled DSRF controller.

Three-level converters are becoming a realistic alternative to the conventional converters in high-power wind-energy applications. In this paper, a complete analytical strategy to model a back-to-back three-level converter is described. This tool permits us to adapt the control strategy to the specific application. Moreover, the model of different loads can be incorporated to the overall model. Both control strategy and load models are included in the complete system model. The proposed model pays special attention to the unbalance in the capacitors' voltage of three-level converters, including the dynamics of the capacitors' voltage. In order to validate the model and the control strategy proposed in this paper, a 3-MW three-level back-to-back power converter used as a power conditioning system of a variable speed wind turbine has been simulated. Finally, the described strategy has been implemented in a 50-kVA scalable prototype as well, providing a satisfactory performance

The direct power control (DPC) technique has been widely used as a control strategy for three-phase power rectifiers due to its simplicity and good performance. DPC uses the instantaneous active and reactive power to control the power converter. The controller design has been proposed as a direct control with a lookup table and, in recent works, as an indirect control with an inner control loop with proportional-plus-integral controllers for the instantaneous active and reactive power errors. In this paper, a model-based DPC for three-phase power converters is designed, obtaining expressions for the input control signal, which allow the design of an adaptive control law that minimizes the errors introduced by parameter uncertainties as the smoothing inductor value or the grid frequency. A controller design process, a stability study of the system, and experimental results for a synchronous three-phase power rectifier prototype are presented to validate the proposed controller.

In this paper, the authors present a controller that directly regulates the active and instantaneous reactive power in a synchronous three-phase boost-type rectifier. The controller ensures a good regulation of the output voltage, and guarantees the power factor close to one. The controller builds upon the ideas of the well known direct torque control (DTC) for induction motors. In their case, the active and reactive powers replace the torque and flux amplitude used as the controlled outputs in DTC, thus motivating the name DPC-control. They show that a simple modification to the original algorithm makes the selection of the control inputs more accurate. To formalize this technique, they utilize the concept of output regulation subspaces. A modification is added to the basic controller to deal with disturbances such as unbalance and distortion in the source voltage. Finally, the proposed controller was tested both in simulations and experimentally, and illustrative results are presented.