Lorenzo Talluri

Dr. Lorenzo Talluri

Università degli Studi di Firenze
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2017 in Energy Conversion and Management
Verified
Journal Article
Closed access
DFD. Fiaschi
D. Fiaschi
GMG. Manfrida
G. Manfrida
ERE. Rogai
E. Rogai
Lorenzo TalluriLorenzo Talluri
Lorenzo Talluri

1 September 2018 in Applied Energy
Verified
Journal Article
Closed access
Lorenzo TalluriLorenzo Talluri
Lorenzo Talluri
DFD. Fiaschi
D. Fiaschi
GNG. Neri
G. Neri
LCLorenzo Ciappi
Lorenzo Ciappi

1 April 2018 in Ocean Engineering
Verified
Journal Article
Open access
Lorenzo TalluriLorenzo Talluri
Lorenzo Talluri
DND.K. Nalianda
D.K. Nalianda
EGE. Giuliani
E. Giuliani

1 July 2016 in Ocean Engineering
Verified
Journal Article
Open access
Lorenzo TalluriLorenzo Talluri
Lorenzo Talluri
DND.K. Nalianda
D.K. Nalianda
KKK.G. Kyprianidis
K.G. Kyprianidis
Theoklis NikolaidisTheoklis Nikolaidis
Theoklis Nikolaidis
PPP. Pilidis
P. Pilidis
In recent years, the increase in marine fuel prices coupled with stricter regulations on pollutant emissions set by the International Maritime Organization have promoted the research in new propulsion technologies and the utilisation of cleaner fuels. This paper describes a novel methodology to enable quantifying and evaluating the environmental and economic benefits that new technologies and fuels could allow in the marine sector. The proposed techno economic and environmental analysis approach enables consistent assessment of different traditional propulsion systems (diesel engine and gas turbine) when operated in conjunction with a novel environmental friendly technology, such as a vertical axis wind turbine. The techno-economic and environmental assessment is focused on the potential reduction in fuel consumption and pollutant emissions that may be accrued while operating on typical Sea Lines Of Communication (Mediterranean, North Sea, Atlantic). The study demonstrates the benefits of the installation of two vertical axis wind turbines on the deck of a ship in conjunction with conventional power plants. The analysis indicates that the performance of the wind turbines and the corresponding benefits strongly depend on the routes and environment in which they operate (therefore favourable wind conditions) allowing fuel savings from 14% (in the gas turbine case) to 16% (in the diesel engine case). The study also indicates that possible benefits may diminish for weak wind conditions. The results reported in this paper establish the economic benefits of installing vertical axis wind turbines in conjunction with conventional technology (Diesel and Gas Turbine Power plants) when installed on a ship travelling through the Atlantic Ocean. The primary purpose of this study is to introduce a methodology to demonstrate the application, performance and economic benefits of the technology at a preliminary design phase and further form a foundation for more elaborate analysis on the subject in the future

1 September 2018 in Energy
Verified
Journal Article
Closed access
GMG. Manfrida
G. Manfrida
LPL. Pacini
L. Pacini
Lorenzo TalluriLorenzo Talluri
Lorenzo Talluri

6 May 2021 in Energies
Verified
Journal Article
Open access
PDF file
MSMoein Shamoushaki
Moein Shamoushaki
Pouriya H NiknamPouriya H Niknam
Pouriya H Niknam
Lorenzo TalluriLorenzo Talluri
Lorenzo Talluri
Giampaolo ManfridaGiampaolo Manfrida
Giampaolo Manfrida
Daniele FiaschiDaniele Fiaschi
Daniele Fiaschi
A comprehensive cost correlation analysis was conducted based on available cost correlations, and new equipment cost correlation models were proposed based on QUE$TOR modeling. Cost correlations for various types of equipment such as pumps, compressors, heat exchangers, air coolers, and pressure vessels were generated on the basis of extracted cost data. The models were derived on the basis of robust multivariable regression with the aim of minimizing the residuals by using the genetic algorithm. The proposed compressor models for both centrifugal and reciprocating types showed that the Turton cost estimation for carbon steel compressor and Matche’s and Mhhe’s data were compatible with the generated model. According to the results, the cost trend in the Turton correlation for carbon steel had a somewhat lower estimation than these correlations. Further, the cost trend of the Turton correlation for carbon steel pressure vessels was close to the presented model trend for both bullet and sphere types. The Turton cost trend for U-tube shell-and-tube heat exchangers with carbon steel shell and stainless steel tube was close to the proposed heat exchanger model. Furthermore, the Turton cost trend for the flat-plate heat exchanger using carbon steel was similar to the proposed model with a slight difference.