Integrated full electric propulsion systems are being introduced across both civil and military marine sectors. Standard power system analysis packages cover electrical and electromagnetic components but have limited models of mechanical subsystems and their controllers. Hence, electromechanical system interactions between the prime movers, power network, and driven loads are poorly understood. This paper reviews available models of the propulsion drive system components: the power converter, motor, propeller, and ship. Due to the wide range of time constants in the system, reduced-order models of the power converter are required. A new model using state-averaged models of the inverter and a hybrid model of the rectifier is developed to give an effective solution combining accuracy with speed of simulation and an appropriate interface to the electrical network model. Simulation results for a typical ship maneuver are presented.
2 November 2006 in IEE Proceedings - Electric Power Applications
An analytical and experimental comparison of the performance of multiphase induction machines as a function of the number of phases is provided. The method of generalised complex harmonic analysis is used to model the multiphase machine, including the calculation of pulsating torques. This general model is validated with experimental results. The test machine used a standard motor frame, which had been modified to bring every coil out to a patch panel. With 12 coils per pole, the machine was tested in 3, 4, 6 and 12-phase operation. Results show moderate reductions in stator losses and significant improvements in pulsating torques.
20 March 2006 in IEEE Transactions on Industry Applications
The paper shows how the techniques of generalized harmonic analysis may be used to simulate the steady-state behavior of a multiphase cage induction motor with any form of open-circuit or short-circuit fault in the stator winding. The analytical model is verified using a four-pole machine with a 48-slot stator. Each coil of the stator winding of this machine is brought out to a patchboard that enables the stator to be configured for single-phase, two-phase, three-phase, four-phase, six-phase, or 12-phase excitation. Experimental results are compared with computer predictions for a six-phase machine with both open-circuit and short-circuit faults.
30 May 2014 in IEEE Transactions on Industrial Electronics
A system compensator is designed to cancel the mechanical characteristics of a power electronics-controlled induction motor drive with a coupled electrical generator system. The emulation scheme using the compensator enables accurate emulation of high-speed and high-power mechanical system dynamics. The compensator is developed based on the system transient response of the test rig, considering the full operating range of the test system. The design process of the compensator is described, and it is validated in both the time and frequency domains. Finally, the effectiveness of the compensator is demonstrated by simulation and experimental emulation of aero gas engine dynamics.
18 March 2015 in IEEE Transactions on Industry Applications
Modern aircraft require a robust and reliable supply of electrical power to drive a growing number of high-power electrical loads. Generators are driven by a mechanical offtake from the variable speed gas turbine (GT), while a constant frequency ac network is preferred. Here, doubly fed induction machines are advantageous since they can be controlled, through a fractionally rated converter, to decouple electrical frequency from the mechanical drive speed, making control of the network frequency possible. However, the converter must be suitably rated, according to drive speed range, electrical voltage and frequency regulation, and power requirements. This paper develops and validates a simulation model of the doubly fed induction generator (DFIG) system, which is applied to find the power flow through the machine's stator and rotor connections over a wide mechanical speed range in order to size the converter. A field-orientated control scheme is implemented, to provide stand-alone voltage and frequency regulation across a drive range of ±40% synchronous speed, on a purpose-built 6.6-kW hardware test platform. Based on the mechanical speed range of an aero GT and the identified converter sizing, the suitability of a DFIG for aero applications is appraised. It is shown that a converter rated at 18% of full system rating can be used to meet the aircraft electrical specifications and offers a potential improvement in aircraft performance, with no additional mechanical components.
26 October 2015 in IEEE Transactions on Industrial Electronics
Wound-field synchronous generators are widely used in aircraft and marine electrical systems. As the electric power requirements increase, there is renewed interest in dc power networks, but the electrical source remains a synchronous generator. The combination of a diode rectifier with a wound-field multiphase generator reduces the voltage ripple on the dc network and increases fault tolerance, compared with an equivalent three-phase system. It also increases the options in terms of the winding design and configuration. This paper uses circuit modeling, including harmonics, informed by static finite-element results, to understand the wound-field generator performance for star and polygon connections of both short- and fully-pitched coils. Experimental results are used to validate the models. A polygon connection of short-pitched coils is shown to give good generator utilization for a healthy machine. However, careful design is required to prevent circulating harmonic currents. Under winding open-circuit faults, the polygon connection requires significant derating, making the star connection the preferred option.