High-temperature structural ceramic materials require stability in terms of thermal and mechanical properties. High entropy oxides (HEOs) are among the emerging novel family of advanced ceramic materials with peculiar functional properties. However, their thermal stabilities and mechanical properties are not well investigated. In this work, HEO systems were synthesized from binary oxides of MgO, CoO, NiO, CuO, and ZnO using solid-state reaction method at high temperature, after obtaining the individual oxides through co-precipitation methods. The phase purity of as-synthesized and sintered samples was characterized using X-ray powder diffraction, while the microstructural investigation was performed using Scanning electron microscopy. Mechanical property of the sintered samples at different sintering times and temperatures was investigated and the sample sintered at a sintering temperature of 1200 °C for 15 h sintering time showed a maximum Vickers hardness of about 16 GPa. This result is comparable with some of the hard ceramic materials, and therefore the materials could be a potential candidate for structural applications.
1 April 2020 in Journal of the European Ceramic Society
In this contribution, a composite from bentonite (B), CoFe2O4 (CF), and hydroxyapatite (HAP) was developed by chemical synthesis route for adsorption of a lead ion, Pb (II) from wastewater. Initially, a composite of B/CF was synthesized by varying the weight ratio of CF, i.e., (1–x)B/(x)CF (x = 0.05, 0.15, 0.25, 0.50), followed by ternary composite synthesis, which was formulated from the sample of (0.85B/0.15CF) and different weight ratios of HAP, i.e., (1–y)[(0.85B/0.15CF)]/yHAP where y = 0.25, 0.35 and 0.45 weight ratios of HAP. The sample of 0.85B/0.15CF was found to be optimal in its adsorption capacity of about 20 mg g−1 from the binary composite samples, while among the ternary composites, a sample with a composition of 0.65[(0.85B/0.15CF)]/0.35HAP revealed an optimum adsorption capacity of about 36 mg g−1, which was then selected for further studies. The adsorption kinetics of Pb (II) by the optimum 0.65[(0.85B/0.15CF)]/0.35HAP sample was studied at different contact times from 30–120 min, where the equilibrium was reached at around 90 min of contact time and the kinetic behavior adopted Pseudo-second order adsorption mechanism. The initial concentration of Pb (II) was also varied from 50–200 mg l−1 to study the adsorption isotherm, which resulted that adsorption capacity of 0.65[(0.85B/0.15CF)]/0.35HAP towards Pb (II) was increased to about 66 mg g−1 and the adsorption isotherm data best fitted with Langmuir adsorption isotherm model. Therefore, the result of this study pinpoints that the present composite material is a potential candidate for the adsorption of Pb (II) ion.
All-oxide thermoelectric modules for energy harvesting are attractive because of high-temperature stability, low cost, and the potential to use nonscarce and nontoxic elements. Thermoelectric modules are mostly fabricated in the conventional π-design, associated with the challenge of unstable metallic interconnects at high temperature. Here, we report on a novel approach for fabrication of a thermoelectric module with an in situ formed p–p–n junction made of state-of-the-art oxides Ca3Co4–xO9+δ (p-type) and CaMnO3–CaMn2O4 composite (n-type). The module was fabricated by spark plasma co-sintering of p- and n-type powders partly separated by insulating LaAlO3. Where the n- and p-type materials originally were in contact, a layer of p-type Ca3CoMnO6 was formed in situ. The hence formed p–p–n junction exhibited Ohmic behavior and a transverse thermoelectric effect, boosting the open-circuit voltage of the module. The performance of the module was characterized at 700–900 °C, with the highest power output of 5.7 mW (around 23 mW/cm2) at 900 °C and a temperature difference of 160 K. The thermoelectric properties of the p- and n-type materials were measured in the temperature range 100–900 °C, where the highest zT of 0.39 and 0.05 were obtained at 700 and 800 °C, respectively, for Ca3Co4–xO9+δ and the CaMnO3–CaMn2O4 composite.