Insulators are very important elements of electric power systems. This paper introduces an analysis of electrical conditions in the area between the conductor and the insulator's upperfitting. The designing of new a composite post insulator is presented with the upperfitting made of insulating material. Previous composite post insulators have had upperfittings made of conducting material metal. 3D analysis of electric-field strength in the insulator and its surroundings are also given. The computation was carried out by using the OPERA Vector Fields program tool. The results of this analysis are presented for both-new and old versions of a composite post insulator. 3D analysis shows that the new version has up to five times lower magnitudes of electric-field strength.

This article presents the development of the theoretical background and the design of an electronic device for monitoring the condition of a gapless Metal Oxide Surge Arrester (MOSA). The device is intended to be used online. Because of the inaccessibility and possible remote location of most surge arresters, it is equipped with a communication system, allowing for the device to convey the measurement of the surge arrester characteristics under any conditions. It is possible to determine the condition of the MOSA by gathering measurements of the surge arrester’s resistive component of leakage current. The leakage current information is sent via data transfer unit to a server and, after interpretation, will be forwarded to the authorised personnel through the surge arrester control centre.

This paper deals with the detection of saturation in the magnetic core of a welding transformer which is a part of a middle-frequency direct current (MFDC) resistance spot welding system (RSWS). It consists of an input rectifier, which produces dc bus voltage, an inverter, a welding transformer, and a full-wave rectifier that is mounted on the output of a transformer. During normal RSWS operation welding transformer's magnetic core can become saturated due to the unbalanced resistances of both transformer secondary windings and different characteristics of output rectifier diodes, which causes current spikes and over-current protection switch-off of the entire system. In order to prevent saturation of the transformer magnetic core, the RSWS control must detect that the magnetic core is approaching the saturated region. The aim of this paper is to present a reliable method for detection of magnetic core saturation that does not require an additional sensor. It is based on the artificial neural network (ANN). Its input is the measured primary current of the welding transformer. The applied ANN is trained to recognize the waveform of the current spikes in the primary current caused by the magnetic core saturation, which is used for magnetization level detection.

Štore Steel Ltd. makes more than 1400 steel grades. The highest costs in steel production from scrap stems from the electric arc furnace electric energy consumption. Electrical energy is used to produce heat energy generated by the burning arc between the graphite electrodes and steel scrap. In general, the balanced heat input of all electrodes is essential. Based on the input of thermal energy from all electrodes, also the possibility of occurrence of hot and cold spots in the electric arc furnace can be determined. Perception of and the elimination of the unequal heat load of electrodes have a major impact on reducing operating costs and increasing the efficiency of the electric arc furnace production. Most authors have modeled the arc furnace as an electrical equivalent circuit, where the electric arc is modeled using the macroscopic approach. In this paper, the microscopic approach to the electric arc model is described, where a set of equations (electrical neutrality, Dalton law, Saha–Eggert) was solved using differential evolution algorithm. The results of modeling were practically confirmed by measuring electric parameters (voltage, current, active power) during the electric arc furnace operation. In November 2016, the investment in a new electrode controller using implemented logic will be carried out.

The paper describes the core heating of ACSR (aluminum conductor steel—reinforced) conductor in stable operation under different environmental conditions. The calculations are greatly simplified in a steady state—we can calculate on a balance of power instead of a balance of energies. At a known surface, the temperature of the conductor due to solar radiation, natural convection, and joules heating as well as the temperature of the steel core were calculated, which is relevant for the tensile strength of the rope. Measurements of the surface of the conductor and the core rejected a simple model of heat transfer—it is also necessary to take into account empty air spaces between the wires of a rope. On the basis of measurements, a new model has given satisfactory compliance with the measured values.

This paper deals with the Differential Evolution (DE) based method for identification of the heat equation parameters applied for the estimation of a bare overhead conductor`s temperature. The parameters are determined in the optimization process using a dynamic model of the conductor; the measured environmental temperature, solar radiation and wind velocity; the current and temperature measured on the tested overhead conductor; and the DE, which is applied as the optimization tool. The main task of the DE is to minimise the difference between the measured and model-calculated conductor temperatures. The conductor model is relevant and suitable for the prediction of the conductor temperature, as the agreement between measured and model-calculated conductor temperatures is exceptional, where the deviation between mean and maximum measured and model-calculated conductor temperatures is less than 0.03 °C.