Pentti Kaikkonen

Mr. Pentti Kaikkonen

Materials and Mechanical Engineering, Centre for Advanced Steels Research, University of Oulu, 90014 University of Oulu, Finland
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 January 2022 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
Sumit GhoshSumit Ghosh
Sumit Ghosh
PKPentti Kaikkonen
Pentti Kaikkonen
VJVahid Javaheri
Vahid Javaheri
AKAntti Kaijalainen
Antti Kaijalainen
IMIlkka Miettunen
Ilkka Miettunen
SPSakari Pallaspuro
Sakari Pallaspuro

5 January 2023 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
PKPentti Kaikkonen
Pentti Kaikkonen
Sumit GhoshSumit Ghosh
Sumit Ghosh
Mahesh SomaniMahesh Somani
Mahesh Somani
JKJukka Kömi
Jukka Kömi

12 January 2021 in Metals
Verified
Journal Article
Open access
PDF file
PKPentti Kaikkonen
Pentti Kaikkonen
Mahesh SomaniMahesh Somani
Mahesh Somani
PKPentti Karjalainen
Pentti Karjalainen
JKJukka Kömi
Jukka Kömi
In the past decade, efforts have been focused on developing very fine, medium-carbon bainitic steels via the low-temperature (typically 300–400 °C) ausforming process, which not only enables shorter isothermal holding times for bainitic transformation at low temperatures, but also offers significantly improved strength. This paper describes static recrystallization (SRX) characteristics of austenite in four medium-carbon 2%Mn-1.3%Si-0.7%Cr steels with and without microalloying intended for the development of these steels. The stress-relaxation method on a Gleeble simulator resulted in recrystallization times over a wide range of temperatures, strains and strain rates. Also, the occurrence of precipitation was revealed. Powers of strain (−1.7 to −2.7) and strain rate (−0.21 to −0.28) as well as the apparent activation energies (225–269 kJ/mol) were in the ranges reported in the literature for C-Mn and microalloyed steels with lower Mn and Si contents. The new regression equations established for estimating times for 50% SRX revealed the retardation effects of microalloying and Mo addition showing reasonable fits with the experimental data, whereas the previous model suggested for ordinary microalloyed steels tended to predict clearly shorter times on average than the experimental values for the present coarse-grained steels. The Boratto equation to estimate the non-recrystallization temperature was successfully modified to include the effect of Mo alloying and high silicon concentrations.

1 August 2021 in Materialia
Verified
Journal Article
Open access
APAarne Pohjonen
Aarne Pohjonen
PKPentti Kaikkonen
Pentti Kaikkonen
OSOskari Seppälä
Oskari Seppälä
JIJoonas Ilmola
Joonas Ilmola
VJVahid Javaheri
Vahid Javaheri
Mahesh SomaniMahesh Somani
Mahesh Somani

21 January 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
SUSampo Uusikallio
Sampo Uusikallio
APAarne Pohjonen
Aarne Pohjonen
PKPentti Kaikkonen
Pentti Kaikkonen
HOHaiko Oskari
Haiko Oskari
JKJukka Kömi
Jukka Kömi

5 December 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
PKPentti Kaikkonen
Pentti Kaikkonen
Mahesh SomaniMahesh Somani
Mahesh Somani
APAarne Pohjonen
Aarne Pohjonen
Vahid JavaheriVahid Javaheri
Vahid Javaheri
JKJukka Kömi
Jukka Kömi
A combination of physical simulation and laboratory rolling experiments, including thermomechanical rolling and low-temperature ausforming, was conducted for designing a suitable processing route to enable phase transformation from austenite to ultrafine bainite in a medium-carbon steel. Following low-temperature ausforming at 500-550 °C, two different cooling and holding paths were tried in the study: (1) water cooling close to martensite start temperature (300 °C), followed by isothermal holding (route A), and (2) air cooling to 350 °C followed by isothermal holding (route B). For reference, a third sample was directly water-cooled to 300 °C after hot rolling without ausforming treatment, followed by isothermal holding (route C). Field emission scanning electron microscopy and electron backscatter diffraction, as well as x-ray diffraction, were employed for microstructural analysis and correlations with the mechanical properties evaluated in respect of hardness and tensile properties. The low-temperature ausforming and subsequent cooling schedules resulted in the decomposition of austenite into ultrafine bainite and some martensite, while stabilizing a fraction of finely divided, carbon-enriched interlath austenite. Results suggested the development of a novel, multiphase bainite-martensite-austenite microstructure, achieved via low-temperature ausforming and subsequent air-cooling (route B), was beneficial in respect of mechanical properties. Most of the bainitic plates were in the range of 50-200 nm with the occasional presence of coalesced plates as wide as 2000 nm. Despite the differences in the microstructure, the mechanical behavior of non-ausformed samples was not significantly different. The technique paves way for developing medium-carbon nanostructured/ultrafine bainitic steels with high mechanical properties achieved via innovative modification of processing routes including low-temperature ausforming. Graphical Abstract