We present Josephson junctions fabricated from high transition temperature superconductor (HTS) $\rm YBa_{2}Cu_{3}O_{7}$ (YBCO) coupled to spiral THz antennas. The fabrication process involved creating a Josephson junction at the center of a superconducting bridge embedded into a THz spiral antenna using irradiation from a focused helium ion beam (FHIB). For low doses of helium irradiation, the junctions had metallic barriers and operated at temperatures as high as 67 K. For higher doses of irradiation, insulator barriers were created. These devices had higher resistance but required cooling to lower temperatures (∼10 K) due to smaller critical currents. Through optimization of the dose and by trimming the width of the junctions we created high resistance devices to improve the impedance match to a spiral antenna. Under 90 GHz radiation, we observe up to 17 Shapiro steps in the I-V curve out to approximately 3 mV at a temperature of 10 K.
Local oscillator sources have become a major technological deficit approaching the terahertz frequencies. For applications, where a narrow linewidth is necessary, such as coherent remote sensing, the best solution to signal generation is frequency multiplication, where phase locking can be easily achieved using the fundamental source. We present an alternative to existing frequency multiplier technologies for cryogenic applications. The device is a superconducting waveguide that has kinetic inductance dependent on the rf current through the device. The nonlinear kinetic inductance is anomalous to a nonlinear optical medium, where the Kerr effect causes 3- or 4-wave mixing, as demonstrated in microwave parametric amplifiers utilizing the same nonlinear effect. In 4-wave mixing, three photons at the fundamental frequency are mixed to generate a single photon at the third harmonic. Dispersion engineering is used to achieve wideband phase matching and phase out harmonics higher than the third. The device length is designed to be the point where most photons are up-converted to the third harmonic. Simulations of these devices lead to expected efficiencies as high as 90%. We report results from a NbTiN frequency multiplier from 34.2 to 104 GHz with efficiency better than 50%.
Progress in superconducting device and detector technologies over the past decade has realized practical applications in quantum computers, detectors for far-infrared telescopes, and optical communications. Superconducting thin-film materials, however, have remained largely unchanged, with aluminum still being the material of choice for superconducting qubits and niobium compounds for high-frequency/high kinetic inductance devices. Magnesium diboride (MgB2), known for its highest transition temperature (Tc = 39 K) among metallic superconductors, is a viable material for elevated temperature and higher frequency superconducting devices moving toward THz frequencies. However, difficulty in synthesizing wafer-scale thin films has prevented implementation of MgB2 devices into the application base of superconducting electronics. Here, we report ultrasmooth (<0.5 nm root-mean-square roughness) and uniform MgB2 thin (<100 nm) films over 100 mm in diameter and present prototype devices fabricated with these films demonstrating key superconducting properties including an internal quality factor over 104 at 4.5 K and high tunable kinetic inductance in the order of tens of pH/sq in a 40 nm thick film. This advancement will enable development of elevated temperature, high-frequency superconducting quantum circuits, and devices.
We report on the fabrication and characterization of superconducting magnesium diboride (MgB2) thin films intended for quantum-limited devices based on non-linear kinetic inductance (NLKI) such as parametric amplifiers with either elevated operating temperatures or expanded frequency ranges. In order to characterize the MgB2 material properties, we have fabricated coplanar waveguide (CPW) transmission lines and microwave resonators using ≈40 nm thick MgB2 films with a measured kinetic inductance of ∼5.5 pH/□ and internal quality factors Qi≈3×104 at 4.2 K. We measure the NLKI in MgB2 by applying a DC bias to a 6 cm long by 4 μm wide CPW transmission line and measuring the resulting phase delay caused by the current dependent NLKI. We also measure the current dependent NLKI through CPW resonators that shift down in frequency with increased power applied through the CPW feedline. Using these measurements, we calculate the characteristic non-linear current parameter, I*, for multiple CPW geometries. We find values for corresponding current density, J*=12–22 MA/cm2, and a ratio of the critical current to the non-linear current parameter, IC/I*=0.14–0.26, similar to or higher than values for other superconductors such as NbTiN and TiN.
24 November 2021 in IEEE Transactions on Applied Superconductivity
Smooth and uniform epitaxial ultrathin MgB 2 films are desired for various electronic applications including hot-electron bolometers and single-photon detectors. However, the growth of ultrathin MgB 2 films on SiC substrates using the Hybrid Physical-Chemical Vapor Deposition was dominated by the Volmer-Weber or island growth mode, which limited the minimum thickness for a conductive MgB 2 film. Here we show the results of a study on the very early stage of the MgB 2 film growth. We find that the root-mean-squared roughness and grain connectivity of ultrathin MgB 2 films grown on C-terminated 6H-SiC( $000\bar{1}$ ) substrate is much better than those on Si-terminated substrate. The result provides a simple solution to growing high-quality ultrathin MgB 2 films for applications.
24 January 2023 in IEEE Transactions on Applied Superconductivity
Ultrathin superconducting MgB 2 films are desirable for device applications and for exploration of new quantum phenomena in reduced dimensions. We have reported recently that smooth ultrathin MgB 2 films can be grown on carbon-terminated SiC substrates using Hybrid Physical-Chemical Vapor Deposition (HPCVD). In this work, we present a thickness dependence study of HPCVD-grown ultrathin MgB 2 films on C-terminated SiC with a focus on the thinnest superconducting films. The thickness of a nominally 2 nm thick MgB 2 film, controlled by deposition time based on thickness calibration data from thicker films, was confirmed by cross-sectional imaging via scanning transmission electron microscopy. We obtained a superconducting transition temperature T c = 27.2 K, a self-field critical current density J c (3K, 0T) = 2 × 10 7 A/cm 2 , and a normal-state sheet resistance near the transition Rs = 44.5 Ω/sq in a 2 nm thick MgB 2 film while its root-mean-square roughness was 0.62 nm. These characteristics make the HPCVD-grown ultrathin MgB 2 films highly attractive for superconducting electronic applications.