A number of modern surface processing methods use an energy flux. The examples include electro-spark deposition (ESD) and laser beam processing (LBP). The work concerns the study of Cu-Mo coatings deposited on C45 carbon steel, which were then eroded with a laser beam. The analysis included the analysis of the microstructure, measurements of macrogeometry and microhardness, corrosion resistance tests of selected areas after laser treatment. The coatings were applied with ELFA-541 and subjected to Nd:YAG laser treatment with variable laser parameters. The problem presented in the work can be used to extend the knowledge of the areas of application of ESD coatings, especially in sliding friction pairs.

Organic–inorganic hybrids based on liquid crystalline symmetrical imine (8Z)-N-(4-((Z)-(4-pentylphenylimino)methyl)benzylidene)-4-pentylbenzenamine (AZJ1) with two aliphatic chains and TiO₂ nanomaterials were obtained and investigated taking into account thr crystallographic form of titanium dioxide i.e., anatase versus rutile. The type of TiO₂ influences the mesomorphic properties of imine AZJ1, as observed by differential scanning calorimetry (DSC) and polarizing optical microscopy (POM) techniques. Fourier-Transform Infrared Spectroscopy (FT-IR) was used to investigate the interactions of oxygen vacancies located on the TiO₂ surface with the studied AZJ1 imine together with studying the influence of temperature. Both imine:TiO₂ anatase versus rutile hybrids possessed the highest occupied molecular orbital (HOMO) levels of about −5.39 eV (AZJ1:anatase) and −5.33 eV (AZJ1:rutile) and the lowest unoccupied molecular orbital (LUMO) levels of about −2.24 eV. The presence of TiO₂ in each hybrid did not strongly affect the redox properties of imine AZJ1. Organic devices with the configuration of ITO/TiO₂/AZJ1 (or AZJ1:TiO₂ anatase versus rutile)/Au were fabricated and investigated in the presence and absence of visible light irradiation with a light intensity of 93 mW/cm². Finally, to analyze defects in the constructed organic devices we used thermal imaging and atomic force microscopy (AFM). The addition of TiO₂ in both crystallographic forms has a positive influence on layer-forming properties that manifests itself as a very homogenous heat distribution for the whole sample.

In this paper, four new aromatic imines containing at least one thiazole-based heterocycle were analyzed in detail by UV–Vis spectroscopy, taking into consideration their chemical structures and interactions with PTB7, a known polymeric electron donor widely used in bulk heterojunction organic solar cells. It is demonstrated that the absorption spectra of the investigated active compositions can be modified not only by changing the chemical structure of imine, but also via formulations with PTB7. For all investigated imines and PTB7:imine compositions, calibration curves were obtained in order to find the optimum concentration in the composition with PTB7 for expansion and optimization of absorption spectra. All imines and PTB7:imine compositions were investigated in 1,2-dichlorobenzene by UV–Vis spectroscopy in various concentrations, monitoring the changes in the π–π* and n–π* transitions. With increasing imine concentrations, we did not observe changes in absorption maxima, while with increasing imine concentrations, a hypochromic effect was observed. Finally, we could conclude that all investigated compositions exhibited wide absorptions of up to 800 nm and isosbestic points in the range of 440–540 nm, confirming changes in the macromolecular organization of the tested compounds. The theoretical calculations of their vibration spectra (FTIR) and LUMO–HOMO levels by Density Functional Theory (DFT) methods are also provided. Finally, IR thermal images were measured for organic devices based on imines and the imine:PTB7 composite.

Planar perovskite solar cells were fabricated on F-doped SnO₂ (FTO) coated glass substrates, with 4,4’-((1E,1’E)-((1,2,4-thiadiazole-3,5-diyl)bis(azaneylylidene))bis(methaneylylidene))bis(N,N-di-p-tolylaniline) (bTAThDaz) as hole transport material. This imine was synthesized in one step reaction, starting from commercially available and relatively inexpensive reagents. Electrochemical, optical, electrical, thermal and structural studies including thermal images and current-voltage measurements of the full solar cell devices characterize the imine in details. HOMO-LUMO of bTAThDaz were investigated by cyclic voltammetry (CV) and energy-resolved electrochemical impedance spectroscopy (ER-EIS) and were found at −5.19 eV and −2.52 eV (CV) and at −5.5 eV and −2.3 eV (ER-EIS). The imine exhibited 5% weight loss at 156 °C. The electrical behavior and photovoltaic performance of the perovskite solar cell was examined for FTO/TiO₂/perovskite/bTAThDaz/Ag device architecture. Constructed devices exhibited good time and air stability together with quite small effect of hysteresis. The observed solar conversion efficiency was 14.4%.

We report on the application of l,d-poly(lactic acid) (l,d-PLA) with dispersed Single-Walled Carbon Nanotubes (SWCN) as a flexible translucent electrode for organic devices. We used commercially available nanotubes in various weight ratios from 0 to 8% dispersed in chloroform polymeric solution by ultrasonication and were drop cast. The created hybrid materials were investigated by differential scanning calorimetry to determine the influence of SWCN content on the thermal behavior, while polarizing optical microscope was used to find the effect of mechanical deformations on the textures. Drop-cast films were studied by optical transmittance, conductivity, dielectric properties and by thermal imaging under applied potential. Thermal imaging provided evidence of visible voltage-activated conduction. Simple mechanical deformation such as bending with stretching at edge to ca. 90 and elongation test were performed. Moreover, interactions between l,d-poly(lactic acid) and SWCN were investigated by FT-IR and NMR spectroscopy. Finally, we can conclude that the thermographic examination of created films permits fast, simple and inexpensive localization of defects on the surface of l,d-PLA:SWCN film, together with the electrical properties of the films.