Shuhong Dai

Dr. Shuhong Dai


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SDShuhong Dai
Shuhong Dai
Xiaoli LiuXiaoli Liu
Xiaoli Liu
NKNAWNIT KUMAR
NAWNIT KUMAR
The present work focuses on investigating the characteristics of the fracture process zone (FPZ) in concrete. The Single-edge notched (SEN) concrete beams under three-points bending are employed for conducting mode I fracture propagation. The displacement fields on the specimen surface and the internal AE signal of specimen are obtained simultaneously in real time by digital image correlation (DIC) and acoustic emission (AE) techniques. The experimental and analytical results indicated that the crack tip position, the crack extension length and the stress intensity factors (SIF) are obtained dynamically and quantitatively by DIC technique, and the length of FPZ is identified, respectively, by DIC and AE techniques in the crack extension process. The distribution of internal AE events is consistent with that of FPZ identified from surface deformation of specimens.

13 November 2024 in Scientific Reports
Verified
Journal Article
Open access
PDF file
QSQinglin Sun
Qinglin Sun
SDShuhong Dai
Shuhong Dai
RHRuiqi Hao
Ruiqi Hao
YXYuxuan Xiao
Yuxuan Xiao
To study the influence of the thickness of a weak interlayer on the deformation and failure characteristics of composite rock mass. Based on the measured data of sand-mudstone interbedded floor rock mass in the Yima mining area, Henan Province, China. Using quartz sand, gypsum, and cement as similar materials make composite rock-like specimens with weak interlayers. The mechanical properties, deformation evolution process, failure characteristics, and acoustic emission laws of rock samples with different interlayer thicknesses under uniaxial compression were studied using the digital image correlation method and acoustic emission monitoring technology. The results show that: (1) With an increase in the thickness of the weak interlayer, there is a corresponding decrease in the compressive strength of the specimen. When the thickness of the weak interlayer exceeds 5 cm, the compressive strength of the composite rock specimen is even less than that of the single weak rock-like. (2) Under uniaxial compression conditions, the strain concentration zone first appears in the weak interlayer part of the composite rock-like specimen. As the pressure continues to increase, the specimen is the first to fail at the position of the maximum strain concentration zone. (3) The thickness of the weak interlayer is an important factor affecting the failure mode of composite rock-like specimens. With the increase of the thickness of the weak interlayer, the composite rock-like specimens change from overall failure to local failure. (4) With the increase of the thickness of the weak interlayer in the middle of the composite rock specimen, the maximum value of the energy released by the single acoustic emission event and the maximum value of the cumulative acoustic emission energy decrease during the compression failure process. The research results can provide a reference for the manufacture of composite rock mass with a weak interlayer and the deformation and failure analysis of composite rock mass.

2 October 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SDShuhong Dai
Shuhong Dai
QSQinglin Sun
Qinglin Sun
RHRuiqi Hao
Ruiqi Hao
YXYuxuan Xiao
Yuxuan Xiao
Complex underground conditions make it challenging to conduct extensive coring, and it is difficult for laboratories to carry out a large number of rock mechanics experiments due to the limited number of cores. Rock-like specimens are commonly used in the laboratory to replace coal-rock specimens. In this paper, rock-like specimens with different proportions are produced to study the mechanical properties, failure characteristics, and acoustic emission laws of rock-like specimens under uniaxial compression. The results show that when the rock-like specimen does not contain gypsum, the stress of the specimen decreases rapidly after reaching the peak stress, which is similar to the mechanical properties of hard brittle rock. When the rock-like specimen contains gypsum, the stress of the specimen decreases slowly after reaching the compressive limit, and the failure of the specimen is gentle, which is similar to the mechanical properties of soft rock. When the specimen lacks gypsum, the strength of the rock-like specimen is larger, and the strength of the specimen is positively correlated with the proportion of cement. When the specimen contains gypsum, the strength of the rock-like specimen decreases sharply, and the strength of the rock-like specimen is negatively correlated with the proportion of gypsum. The maximum acoustic emission ringing count increases with higher cement content but decreases with increased gypsum content. The cumulative count change of acoustic emissions approximately underwent four stages, aligning well with the four stages of uniaxial compression failure observed in typical rock. The research results have important reference value for the selection of rock-like materials to replace the original rock materials for laboratory research.

31 July 2025 in Polymers
Verified
Journal Article
Open access
PDF file
CDChangshen Du
Changshen Du
SDShuhong Dai
Shuhong Dai
QSQinglin Sun
Qinglin Sun
Liquid crystal elastomers (LCEs) have shown great potential in the field of soft robotics due to their unique actuation capabilities. Despite the growing number of experimental studies in the soft robotics field, theoretical research remains limited. In this paper, a dynamic model of a bionic arm using an LCE fiber as artificial muscle is established, which exhibits periodic oscillation controlled by periodic illumination. Based on the assumption of linear damping and angular momentum theorem, the dynamics equation of the model oscillation is derived. Then, based on the assumption of linear elasticity model, the periodic spring force of the fiber is given. Subsequently, the evolution equations for the cis number fraction within the fiber are developed, and consequently, the analytical solution for the light-excited strain is derived. Following that, the dynamics equation is numerically solved, and the mechanism of the controllable oscillation is elucidated. Numerical calculations show that the stable oscillation period of the bionic arm depends on the illumination period. When the illumination period aligns with the natural period of the bionic arm, the resonance is formed and the amplitude is the largest. Additionally, the effects of various parameters on forced oscillation are analyzed. The results of numerical studies on the bionic arm can provide theoretical support for the design of micro-machines, bionic devices, soft robots, biomedical devices, and energy harvesters.

7 June 2023 in Experimental Techniques
Verified
Journal Article
Closed access
PDF file
SDShuhong Dai
Shuhong Dai
YXY. Xiao
Y. Xiao
YWY. Wu
Y. Wu
XWX. Wen
X. Wen

27 January 2022 in Crystals
Verified
Journal Article
Open access
PDF file
HGHong Gao
Hong Gao
SDShuhong Dai
Shuhong Dai
A main challenge in the large-scale application of the microbially induced carbonate precipitation (MICP) technique includes the low efficiency of the cementation of coarse grains. Actually, in the MICP treatment process, the cementation effect of the bonding points was more important than pore filling due to the large porosity for coarse grains. To achieve a better cementation effect at bonding points between coarse particles, the quick formation and growth of a biofilm is necessary. In this study, an optimized medium was proposed to improve the cementation effects for coarse materials. The optimized medium and other different media were used for bio-cementation tests with MICP. The viable cell concentrations, strengths, microscopic characteristics, biofilm contents, and calcium carbonate (CaCO3) contents were used to evaluate the bio-cementation and its effects. In bio-cementation tests, the optimized medium led to increased CaCO3 precipitation at the bonding points and better cementation effects compared to other media. Indeed, the strength of the sample treated with the optimized medium was more than 1.2–4 times higher that of the values for other media. The advantages of the optimized medium were demonstrated via bio-cementation tests.